Storing Cookies (See : http://ec.europa.eu/ipg/basics/legal/cookies/index_en.htm ) help us to bring you our services at overunity.com . If you use this website and our services you declare yourself okay with using cookies .More Infos here:
https://overunity.com/5553/privacy-policy/
If you do not agree with storing cookies, please LEAVE this website now. From the 25th of May 2018, every existing user has to accept the GDPR agreement at first login. If a user is unwilling to accept the GDPR, he should email us and request to erase his account. Many thanks for your understanding

User Menu

Custom Search

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY  (Read 11719925 times)

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #165 on: October 01, 2012, 03:02:06 PM »
Which schematic do you refer to, when you write this ?:

I'm building to the Dally 2012 schematic which shows the PSU powered from rectified L4 winding with one leg to earth ground.

Assuming the rail voltages shown are unloaded to convention, then I cannot see how he could get enough voltage from the L4 winding to run the PSU. Having said this, I've not applied the nano pulse yet, so together with the earth ground connection this may produce the magic.

Regards
Hoppy

verpies

  • Hero Member
  • *****
  • Posts: 3473
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #166 on: October 01, 2012, 03:23:21 PM »
I'm building to the Dally 2012 schematic which shows the PSU powered from rectified L4 winding with one leg to earth ground.
There are many schematics floating around. Which one do you refer to?
This one, or this one, or this one, or some other one...





Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #167 on: October 01, 2012, 03:41:11 PM »
There are many schematics floating around. Which one do you refer to?
This one, or this one, or this one, or some other one...

Neither of these. I have attached what I think was the original for his demo.

Regards
Hoppy

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #168 on: October 01, 2012, 06:31:02 PM »
Just tested an old 200W 230V AT PSU on a variac and found that I could reduce the voltage down to 100V with 10.8V output. When loaded with a 10R resistor, voltage fell to 9.5V. However, a higher voltage is needed to start-up the PSU. The PSU does not have a 230v / 115V mains voltage selector switch. Dally reports that although the schematic shows an ATX PSU, he actually used an AT PSU.

Regards
Hoppy

d3x0r

  • Hero Member
  • *****
  • Posts: 1433
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #169 on: October 01, 2012, 08:25:26 PM »
In either case of the prior 2 shematics.  Aren't there a lot of redudnant capacitors in the upper left corner on the +5 volts from the voltage regulators?  Aren't they redudnant of the other caps nearby? 


I ended up only capping the input and output basically with one set of 100nf + 100uf caps, and it has a very stable voltage...


I get 100 volts in my L4 coil from basically just the 4khz TL494 generator, and 150V resonance in secondary (not really resonsance, it looks more like a 8 step ringdown, have to fix the cap on that)


There's no current to the power, just volts.
My nanopulser isn't working, the gate on the KT926 ( I've been working with Hoppy's version) is held open toooo long... probably should have gotten the 14ns gate delay 74hc00 instead of 7; I'm not getting very square waves

verpies

  • Hero Member
  • *****
  • Posts: 3473
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #170 on: October 02, 2012, 01:35:59 AM »
In either case of the prior 2 shematics.  Aren't there a lot of redudnant capacitors in the upper left corner on the +5 volts from the voltage regulators?  Aren't they redudnant of the other caps nearby?
These capacitors are there for bypassing power supply rails - there is never too much of that.
They are not redundant because electrolytic capacitors have low-ESR at low frequencies and ceramic capacitors have low-impedance at high frequencies, thus they complement each other.

The digital ICs like to have a clean power supply.

Ganzha

  • Full Member
  • ***
  • Posts: 156
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #171 on: October 02, 2012, 01:57:04 AM »
this is really fake matter :-[

Vortex1

  • Hero Member
  • *****
  • Posts: 518
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #172 on: October 02, 2012, 04:23:08 AM »
Are they external power source wires or grounds?

Since one of them goes directly to the AC terminal of the bridge rectifier the other connects to L4 the opposite end of which then goes to the other AC terminal, they can be suspect.

It is disturbing, as it agrees with the schematic, but could also be external power wires.

Anyone have a rotation of the device and positive identification? Do they exit from the braid?

I cannot tell by zooming as resolution is too low.

d3x0r

  • Hero Member
  • *****
  • Posts: 1433
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #173 on: October 02, 2012, 04:56:43 AM »
These capacitors are there for bypassing power supply rails - there is never too much of that.
They are not redundant because electrolytic capacitors have low-ESR at low frequencies and ceramic capacitors have low-impedance at high frequencies, thus they complement each other.

The digital ICs like to have a clean power supply.


Sure I understand having the ceramic and foil caps... but so many sets of them?  on the +5 to the first chip that generates the steady frequency (leftmost chip) there is a set coming off the power regulator, another set right next to the chip and another set at the resistors...  The other chip only has a set of capacitors between the voltage regulator and +5 of the chip...

d3x0r

  • Hero Member
  • *****
  • Posts: 1433
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #174 on: October 02, 2012, 04:59:46 AM »
this is really fake matter :-[


what makes you say that?   I don't understand the arrows, or the caption in russian

d3x0r

  • Hero Member
  • *****
  • Posts: 1433
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #175 on: October 02, 2012, 05:05:06 AM »
Are they external power source wires or grounds?

Since one of them goes directly to the AC terminal of the bridge rectifier the other connects to L4 the opposite end of which then goes to the other AC terminal, they can be suspect.

It is disturbing, as it agrees with the schematic, but could also be external power wires.

Anyone have a rotation of the device and positive identification? Do they exit from the braid?

I cannot tell by zooming as resolution is too low.


There is the corner ground connection.  The garden video shows the device in entirety more than the benchtop videos.


http://www.liveinternet.ru/users/edward_lee/post235549906/play




I suppose, he could be using something like phone wire for the ground connection, and have two leads bringing in AC, which would go out the bottom near the ground point it's connected to....






Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #176 on: October 02, 2012, 07:48:26 AM »

There is the corner ground connection.  The garden video shows the device in entirety more than the benchtop videos.


http://www.liveinternet.ru/users/edward_lee/post235549906/play




I suppose, he could be using something like phone wire for the ground connection, and have two leads bringing in AC, which would go out the bottom near the ground point it's connected to....


I think Ganzha is probably right and we are looking at a fake. IMO it could be something similar to the Aqua2 trick, in this case with the braid acting as the mains neutral and inside, carrying a 'live' conductor going back to the domestic supply in the house. This is like TK used for the Aqua2, a braided cable sheath / hose, not ordinary braided earth strap, as it can be seen to be much wider where its clamped with the earth bolt. Only thin conductors are needed for the low energy flouro lamp. Although, fairly obvious from the coil winding ratios, I have already established that with the rail voltage levels shown on the schematic, insufficient voltage is available from L4 to run the PSU. L4 is most likely carrying the mains live feed through to the bridge rectifier. If this is a fake, then Dally is right on one point - that the earth wire is essential for operation of the device  ;D

I will cease work on this project to let this one play out. T1000 has already advised us to hang fire and wait developments from Dally.

Regards
Hoppy

T-1000

  • Hero Member
  • *****
  • Posts: 1738
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #177 on: October 02, 2012, 09:41:02 AM »
this is really fake matter :-[
Littering thread with single photo again? Dally provided another photo on 90 degrees, there is your answer to wires.

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #178 on: October 02, 2012, 10:12:52 AM »
Littering thread with single photo again? Dally provided another photo on 90 degrees, there is your answer to wires.

T-1000

I've just looked carefully at photo 08 on Dally's website and it clearly shows the two white wires soldered to a tag which is clamped to the earth braid with a bolt. So, if there was a 'live' mains feed into the board, it was not connected at this point as far as I can see. the braid could still act as a neutral conductor with a 'live' wire entering the board at another point. Both the garden video and work bench videos unfortunately leaves a lot of scope for a hidden wire, so its not surprising that 'fake' is being called.

Regards
Hoppy

verpies

  • Hero Member
  • *****
  • Posts: 3473
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #179 on: October 02, 2012, 10:29:16 AM »
Are they external power source wires or grounds?

Since one of them goes directly to the AC terminal of the bridge rectifier the other connects to L4 the opposite end of which then goes to the other AC terminal, they can be suspect.

It is disturbing, as it agrees with the schematic, but could also be external power wires.
They could be, but I think it is too early to look for fakery because we do not have any failed replication attempts yet.

I think it very likely that Dally's device is a PsyOp designed to distract from the real McCoy however not because of ambiguous fuzzy photo interpretations but rather due to the absence of a Gain Medium, which is the success determining feature for me.

Dally device contains an exotic nanosecond pulser based on newly discovered DSRD devices. While it is an exciting project in itself, it is also a promising technique for eliciting energy releasing NMR and EPR in various gain media, as described by McFreey and without the difficult tunning of single frequency systems. (contrastingly, nanopulses consist of dense comb of frequencies).

The objective of this PsyOp would be to associate the nanopulsing technique with failure, effectively discouraging people from building devices using this technique because it is the surest way to stimulate energy release from Gain Media without the tuning difficulties exhibited by schemes such as the Yoke Device.

Also, a month ago somebody posted a link on the Kapanadze thread to video of a Russian inventor, who showed a self-running pulsed device that looked almost like the Dally device but contained a Gain Medium made out of ferrite rings.  The author clearly said at the end of the video "so there are not any doubts, let it be clear, that the device uses a ferrite core" and took the core pieces out of the cylindrical tube. 
A week later  a very similar but "coreless" Dally device appeared.

I looked but could not find that video again - but maybe it is still there, buried somewhere.