Storing Cookies (See : http://ec.europa.eu/ipg/basics/legal/cookies/index_en.htm ) help us to bring you our services at overunity.com . If you use this website and our services you declare yourself okay with using cookies .More Infos here:
https://overunity.com/5553/privacy-policy/
If you do not agree with storing cookies, please LEAVE this website now. From the 25th of May 2018, every existing user has to accept the GDPR agreement at first login. If a user is unwilling to accept the GDPR, he should email us and request to erase his account. Many thanks for your understanding

User Menu

Custom Search

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY  (Read 11719010 times)

Bat1Robin2

  • Jr. Member
  • **
  • Posts: 94
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8355 on: April 21, 2015, 06:16:12 AM »
Geo fusion,
I am using 800 ohm 7 watt resistor on the bemf  R26 back to power supply as schematic shows 1k ohm but wattage not labeled. i believe that bemf power is being used by the tesla circuit but im not sure. 1/4 burned out and 2 watt blackened , 7 watt goes to 140-150 degree but holding with my smaller fets its doing ok. so i recommend higher wattage until it holds.

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8356 on: April 21, 2015, 09:32:38 AM »
Hi there Guyz  ;)

Finaly got my vid to be uploaded, and was busy today on the bench to see some
amazing effects. there is still so much more to try out but Thoughts are welcome and help.

https://www.youtube.com/watch?t=156&v=aOSkep6jZnA

Bat1Robin2, Nice setup, it's going in the right path but see if you can get your hands on
IRFP260's or IRPF450's or better :) . but awesome results thought ,Keep o experimenting!.
And yes, Give the both Yoke and Freq generator individual power supplies, or sources from one core.
Driven by another TL494 or different ;) , giving thoughts.

Lost_bro,
 You are thinking how I had it in mind a year ago :) , Using SSTC or DRSSTC type driver circuits , It's basically that but reinforced.

Nickz, yes I still have the Vid on my channel, it's there for the view :) , check it out, But I have learned from the Ruslan Vid completely
that is how I managed to build the coil and using the schema too.

magpwr, try my Flyback experiment with a coil setup :) !, but not with 12 or 24Vdc, but with +100Vdc, and us the ground. and good
HV caps, there you will see results, I have made a High power Mazilli, that can handle those voltage ratings and yes there is more power
and yet dangerous high voltage acs to ground., this is done with 12V battery connected to inverter  and rectified.

Let me know if you guyz want the schema of the circuit. I did post it some time ago ;)

cheerz

Hi Geo,

Its good to see that you have now built the PWM push-pull module of Akula's setup.

What current are you drawing from the 24V supply?

Tip: You need some decent wire connections onto your lamps.  ;)

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8357 on: April 21, 2015, 01:39:34 PM »
  Geo:
   Thanks for posting your video.  Can I ask you where you obtained the 1000w bulbs?
  Those new bulbs seem to put out less light (lumins) than your round core test lighting the 1000w halogen bulb:
 https://www.youtube.com/watch?v=QRBI39us0VI
  Which had used the Royer crt and the yoke core back then.  But, you couldn't keep it lit more than a few seconds, without burning the fets.
  And so far it's also giving less light compared to my current set up, which is running off of only 12v, or less. 
  So, I'm still waiting to see the "awesome" results,  when you connect it all up to the grenade and Kacher, and get it self running.

Dog-One

  • Hero Member
  • *****
  • Posts: 1019
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8358 on: April 21, 2015, 08:37:32 PM »
I am using 800 ohm 7 watt resistor on the bemf  R26 back to power supply as schematic shows 1k ohm but wattage not labeled. i believe that bemf power is being used by the tesla circuit but im not sure. 1/4 burned out and 2 watt blackened , 7 watt goes to 140-150 degree but holding with my smaller fets its doing ok. so i recommend higher wattage until it holds.

The attached circuit most certainly works and I also agree you need R26 to handle all the reflected power fed into the toroid when the secondary is unloaded.  I'll order some TWM10 resistors and see how things behave.

Funny to think how a simple power inverter can bog us down so easy.  Hopefully we can get past that and start exercising the grenade coil.

T-1000

  • Hero Member
  • *****
  • Posts: 1738
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8359 on: April 21, 2015, 09:31:27 PM »
Hi,

I had conversation with Oleg (who made circuits for Ruslan) yesterday and he shared some links to forum (pass through Google translate):
http://realstrannik.com/forum/dosae-initiative/228-foreigner-skhemy-2-2.html
http://realstrannik.com/forum/ustanovka-kulabukhova/213-skhemy.html?start=108#9074

His nickname in that forum is Foreigner, you can ignore other people there.

Also here is offline copy of his circuits and PCBs:
http://filebin.net/84mauc7noc/Kapanadze_replica_-_Ruslan.zip

Hopefully that helps with electronics part.

Cheers!

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8360 on: April 21, 2015, 11:22:57 PM »
    Thanks for that, T-1000.
   I knew that it wasn't Ruslan making all those different pcb circuits. So, it's Oleg...
   Now, as you've talked to the actual board designer, maybe he would be willing
to sell us some of those boards.  That's, what I'm looking for. Buy it, mount it, and use it,
without all the unknowns and testing, we are facing now. At least, once they find which ones works best.
   But, in any case there lots of very useful information in that 24 MB download.
    Thanks again.
                         NickZ

Bat1Robin2

  • Jr. Member
  • **
  • Posts: 94
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8361 on: April 21, 2015, 11:39:31 PM »
T- 1000,
Thanks so much for the links and information this is the first time i have seen the Tesla powered from 130-135dc ( i have been using 24), i could not make that out on my schematic.
Have you made this device?
What was your efficiency achieved?
Also C15 1 see its a 1 ufd but what type of capacitor is that?

My setup runs the push pull at about 27khz range. The tesla is being pulsed at the same frequency as the yoke but has a 1.25khz ring-down and barely produces a field able to light a CFL. but it is powered with 24 v DC.  It seems to pulse exacly when the bemf hits the 24 volt line from the yoke drive fets.
Does this all sound correct or am doing something wrong?
I can light 4-5 bulbs but can only reach 70% efficient.



NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8362 on: April 22, 2015, 12:14:16 AM »
  Bat1:
  Remember that to obtain 70% efficiency, your bulbs would have to be the same brightness, as when when they are run on the grid.
  Now, Ruslan is using a two transistor Kacher circuit, as each new crt is different from the previous one.
 

Dog-One

  • Hero Member
  • *****
  • Posts: 1019
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8363 on: April 22, 2015, 12:27:14 AM »
Yes, thank you again T.  Most useful and it confirms my suspicion Ruslan wasn't using Vector boards--I don't think he could solder well enough to get anything to work if he did.   :)

Now that I know what is needed, I'll get some boards made up.  This will be a big step forward.

Also C15 1 see its a 1 ufd but what type of capacitor is that?

I used a polypropylene type like so:
http://www.mouser.com/ds/2/427/mkp-mkp378-239714.pdf

magpwr

  • Hero Member
  • *****
  • Posts: 1168
    • Youtube Channel
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8364 on: April 22, 2015, 12:44:52 AM »
T- 1000,
Thanks so much for the links and information this is the first time i have seen the Tesla powered from 130-135dc ( i have been using 24), i could not make that out on my schematic.
Have you made this device?
What was your efficiency achieved?
Also C15 1 see its a 1 ufd but what type of capacitor is that?

My setup runs the push pull at about 27khz range. The tesla is being pulsed at the same frequency as the yoke but has a 1.25khz ring-down and barely produces a field able to light a CFL. but it is powered with 24 v DC.  It seems to pulse exacly when the bemf hits the 24 volt line from the yoke drive fets.
Does this all sound correct or am doing something wrong?
I can light 4-5 bulbs but can only reach 70% efficient.

hi Bat1Robin2,

I think i have left out efficiency measurement during my experiment.
It would make sense if the setup is running below 80% efficiency then it's obvious to get a boost via reflected current pulse if coming from Earth would not help as well.

Applying high voltage for tesla coil even at nearly 200volts did not produce any current movement to Earth.

Only via capacitor discharge through the primary coil of tesla coil whatever the design did produce current reading in Amps to Earth.
I don't wish someone else to waste their time by merely working on high voltage tesla coil without the pulse capacitor element.

Do try to use low power like 60watt or 100watt bulb for a start.

Bat1Robin2

  • Jr. Member
  • **
  • Posts: 94
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8365 on: April 22, 2015, 04:04:51 AM »
  Bat1:
  Remember that to obtain 70% efficiency, your bulbs would have to be the same brightness, as when when they are run on the grid.
  Now, Ruslan is using a two transistor Kacher circuit, as each new crt is different from the previous one.
 
You must be confused efficiency is the output/input power .. nothing to do with bulb brightness. i can have 1 bulb on really bright at 50% efficient but light 4 bulbs medium brightness calculated at 70% . i measure output current and voltage DC and then compare to input voltage and current DC. no funny waveforms straight dc. I totally ignore the wattage on the bulbs and there brightness they are not accurate until 120 is reached. i think we agree just in different words. How can anyone do this project and not measure input vs output?
I have sent a few pictures. Im afraid the hard reality of output is always less than input is hitting me right on the calculator screen. The tesla seems to enable the output somehow but nothing more than addition of the 2 input sources. i will try to increase tesla supply in the next few days but i have already noticed the supplies dont like to be separated somehow the bemf from the yoke helps the tesla or vise versa. look at the pictures and notice that when the tesla spike happens it actually stops the drive input on the yoke half way thru the square wave drive i believe this is what causes the current to reduce in the power supply. since most of the power is feeding the yoke cutting that drive signal off early is what helps reduce input.

Bat1Robin2

  • Jr. Member
  • **
  • Posts: 94
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8366 on: April 22, 2015, 04:23:08 AM »
closely look at picture 13 drive signals only no power to FETs
Then look at picture 16 with bulbs in background and how it cuts off the drive to the yoke exactly when the yoke spikes.

Bat1Robin2

  • Jr. Member
  • **
  • Posts: 94
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8367 on: April 22, 2015, 04:24:36 AM »
sorry i mean right at telsa spikes. its stops the yoke fet for the rest of that square wave. ok im done posting for a while sorry.

Tomtech29

  • Sr. Member
  • ****
  • Posts: 447
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8368 on: April 22, 2015, 08:36:54 AM »
T-1000 Thank you for your support for a long time already and there was no sign on here alive.
-a lot of interesting information, I think that this time the scheme is closer to the truth?
(I'm only bothering diagram which introduces a lot of confusion and lack of measurement synchronization center)

magpwr "here is a little of truth no matter how to perform a security gate of the power transistor (IRFP260)... soundproofing signal through the varistor zener diode combinations? there comes a point while tuning and gets a kick mortal!.

hello forum participant  "Bat1Robin2" I do not know where you got these readings,I did not see how to fix your configuration LC series circuit if you could throw a link to the video,I know that when you have a lower tuning frequency of the inductor is needed to sync while we choose one of the harmonics at high frequencies where the Tesla 1,7Mhz when you turn on the pulse peaks spend Kacher I think that in a short time Ruslan show us how they look pulses I run and greet all.

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #8369 on: April 22, 2015, 03:34:43 PM »
  Bat1 and All:
  Remember to resize your pictures.
  What I see on my set up is that unless the Kacher is in sync with the induction crt,  the addition of a ground line or feed-back path onto the rest of the circuit, won't do much.
  On the other hand, if and when they are in sync, then you see that the addition of the Kacher it will not disrupt their superimposed signals, but will aid it instead.
   Adding the ground line(s) will only add to the circuits output when the two circuits are in sync, or close to it. Otherwise little to no improvement will be noticed. At least on my device.
  I don't think that neither Akula or Ruslan are comparing the input levels to the output readings when tuning. Nor have I heard them talk about that, as an important factor. Plus, it may not be dependent on that at all, for their devices to work in a self running mode.