Storing Cookies (See : http://ec.europa.eu/ipg/basics/legal/cookies/index_en.htm ) help us to bring you our services at overunity.com . If you use this website and our services you declare yourself okay with using cookies .More Infos here:
https://overunity.com/5553/privacy-policy/
If you do not agree with storing cookies, please LEAVE this website now. From the 25th of May 2018, every existing user has to accept the GDPR agreement at first login. If a user is unwilling to accept the GDPR, he should email us and request to erase his account. Many thanks for your understanding

User Menu

Custom Search

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY  (Read 11719108 times)

stupify12

  • Full Member
  • ***
  • Posts: 175
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7530 on: December 11, 2014, 06:26:42 PM »
Hello

You are using a Solid State High Frequency Generator, because this device only produce continouse waveform which is not what Nikola Tesla wanted to perform on his device. So this brilliant Akula has find a way to replicate Nikola Tesla High Frequency Generator and combine with a Kacher which people think is a superimposed controller.

I think the Kacher here works as a Spark Gap that breaks the High Frequency Generator Signal into a sudden Impulse.

The Tesla 1 Wire Transmission is much more elaborated in the Tesla Book. You can see all you need on that book, the conversion of High Voltage with lesser Amperage into a High Amperage thick Secondary..


Meow   8)

   So, it looks to me that the idea is too radiate Hv pulses from the Kacher onto the grenade's 12, 12, or to the 24, 24, induction coil, which is also connected to the yoke's three turns coil. The three turns coil circuit with it's tuning cap, is also connected to the 25 to 28 turns coil (by the single jumper wire), as well as all three of these circuits (including Kacher) to an earth ground.
So, what's going on here???
  There are three different circuits being pulsed at the same time.
   Has anyone had even the slightest noticeable results, meaning higher output, (bulb brightness), when the Kacher is attached, as compared to without it working?

 

 

stupify12

  • Full Member
  • ***
  • Posts: 175
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7531 on: December 11, 2014, 06:33:36 PM »
Hi Hoppy,

Can you share me a good TL494 push pull oscillator schematic diagram, like the one you are describing on this post. Thanks in advance..

Meow ;D

The description I gave was with both the push-pull and Kacher working. When the Kacher is switched on, the bulb can be taken from low light to full brightness by tuning and then to no light output just by hand capacitance - moving the hand close to the antenna.

This Ruslan setup using the yoke has poor efficiency as a transformer and cannot light a 1000W bulb (with or without grenade & Kacher) very brightly when driven with a Mazilli or TL494 driven push-pull oscillator at 12V or 24V working. This is why I can only get full bulb rated voltage (240V) across a 40W lamp with the help of the Kacher. With a 60W or 100W bulb, the voltage across them drops and therefore so does the light output. As Jeg has commented, your load is way to high to see any significant effect from the Kacher.

Yes, I have tried looping back and nothing happens in respect of seeing any signs self-running. Its time to focus on the concept of operation because the Ruslan device as demonstrated and circuit as drawn is either fake or we are missing a vital part of the build.

magpwr

  • Hero Member
  • *****
  • Posts: 1168
    • Youtube Channel
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7532 on: December 11, 2014, 07:02:50 PM »
hi everyone,

There is something i would like to share which is base on my previous experimental findings.

For those whom are using TL494 or SG3525 or UC3825 for the PWM generator.You will notice that even though you preset to a frequency.
This Pwm generator base on my previous observation is that it will slowly drift in frequency at 1 or 2 decimal place.Even though you are using a better capacitor to ensure the frequency stability.

The reason why i stick with LTC1799 SOT23 is that base on few youtube video the frequency drift is in 2nd or 3rd decimal place.The output will be split into 2 via my 74HC132 PWM generator.

But the best approach is to use PLL recall the posting by Enjoykin couple of weeks back.The toroid which is generating the mustache which shot at peak at certain frequency will be fed to LM358 comparator.

The other unofficial approach is the antenna approach  which is fed to dual 4017 to get divide by 60.
 ----------------------------------------------

Lastly please do not use plastic or plastic bottle to hold the antenna coil in place. Reason is simple although plastic isn't electrically conductive but it is still able to conduct static electricity somehow which dampen the effect.

----------------------------------------------
I do hate placing orders online during this time of the year.Goods hardly reach my door within 2 weeks.


 

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7533 on: December 11, 2014, 08:36:35 PM »
Hi Hoppy,

Can you share me a good TL494 push pull oscillator schematic diagram, like the one you are describing on this post. Thanks in advance..

Meow ;D

Hi Meow,

I do not have a circuit diagram of the exact design I used but its close to Ruslan's circuit I modified attached. I suggest you use Itu's mosfet protection components as shown in post no.7511.

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7534 on: December 11, 2014, 08:41:25 PM »

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7535 on: December 11, 2014, 08:49:06 PM »
Hello everyone  ;D

I have read all your post, comments and suggestion. I ask of those who has worked with a Kacher circuit did you get a good results? Anyone?
This is not a discouragement but a suggestion for a better development on this project.

The secret you are looking for has been answered by Enjoykin many times. The Ruslan and Akula schematics are very pleasing to your eyes, but if follow those Coil Winding or Coil Arrangement you end up in failure.. I think all of us here knows that this Ruslan, Akula, and many others which has succeed on this Free Energy device has research only the work of Nikola Tesla. The answer which you think is a secret has already been in you memory drives(Brain).

The very first hint to success on this device is what Tariel Kapanadze called  "Tesla Transformator" which he is actually telling us the Tesla Electrical Transformer patent which also Nikola Tesla elaborate more this device on his Book. 

Why the Akula or Ruslan device needed a Kacher circuit? On I have observed, which was also tested by me. When I try to directly connect the Tesla 1 Wire Transmission to the Receiving Transformer the bulb attach will not light even a little, also the capacitor attach in a Radiant Receiving Element fashion is not charging. But if the Tesla 1 Wire Trasmission line is switch thru a Spark Gap, the bulb will light brightly, the capacitor will discharge automatically on its own terminal. When another windings are rectified to charge Capacitor can run a DC motor when attach to this capacitor. 

What is lacking is a conversion of this electrostatic charge in a capacitor to be switch by another switching Electronics or Spark Gap that the frequency will be 60hz with smaller potential(voltage), greater amount of current(amperage). Like the Switching Power Supply does on the computer PSU, Convert the stored electrostatic charged in a Conventional way like all of us here knows then feed it back to your device..




Meow 8)

Hi Meow,

Can you please put some flesh on the bones by explaining how the 1-wire transmission system switched through a spark gap is powered?

d3x0r

  • Hero Member
  • *****
  • Posts: 1433
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7536 on: December 11, 2014, 08:53:45 PM »
was fiddling with a small signal transistor; with a high hfe... was trying to get it to get tickled at higher frequencies, and managed to get it... for a bit to be at 2-3Mhz and low power draw, when I increased the power I had it connected to the grenade through a 2.2nF cap and managed to get 80+ volts out... but it stopped.  It was working for a few minutes great...
(mind you 2.2nF is huge for 2Mhz and < 100mA)

Telsa valve.... for blocking/passing impulse fluid currents...
http://www.tfcbooks.com/patents/1329559.htm

Coil reminds me of one loop extruded in a circle...
*shrug*

stupify12

  • Full Member
  • ***
  • Posts: 175
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7537 on: December 11, 2014, 09:17:29 PM »
Hello Hoppy,

I think using DIODE is good, but I believe semiconductor are only a waste of energy. I show you how Tesla do it with his old technology rotating wheels, how did Tesla obtain consistent sign of charging to his Very Big Electrostatic Condenser. I mean consistent sign, If the wave is positive it will be put to the Positive Terminal of the Condenser, If the wave is Negative it will be put to the Negative-Grounded Terminal..

On the circuit I have drawn, the sign of the wave that will be charge on the capacitor will match with the polarity of the Capacitor so in every Impulse of the Spark Gap the energy on the Condenser is exponential...

Btw. Dont forget to calculate the quarter wavelength for the length of secondary. If not quarter wavelength, the wavelenth of the velocity of the light disturbance will be Multiplied with odd numbers like 1, 3, 5, 7, 9 .. I think people should begin to study only Nikola Tesla nothing else all the answer you need is described and cited by Nikola Tesla in a very great detail..


Meow   8) 8)

Hi Meow,

Can you please put some flesh on the bones by explaining how the 1-wire transmission system switched through a spark gap is powered?

skywalker66

  • Full Member
  • ***
  • Posts: 182
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7538 on: December 11, 2014, 10:36:30 PM »
Hello Hoppy,

I think using DIODE is good, but I believe semiconductor are only a waste of energy. I show you how Tesla do it with his old technology rotating wheels, how did Tesla obtain consistent sign of charging to his Very Big Electrostatic Condenser. I mean consistent sign, If the wave is positive it will be put to the Positive Terminal of the Condenser, If the wave is Negative it will be put to the Negative-Grounded Terminal..

On the circuit I have drawn, the sign of the wave that will be charge on the capacitor will match with the polarity of the Capacitor so in every Impulse of the Spark Gap the energy on the Condenser is exponential...

Btw. Dont forget to calculate the quarter wavelength for the length of secondary. If not quarter wavelength, the wavelenth of the velocity of the light disturbance will be Multiplied with odd numbers like 1, 3, 5, 7, 9 .. I think people should begin to study only Nikola Tesla nothing else all the answer you need is described and cited by Nikola Tesla in a very great detail..


Meow   8) 8)

YESSS! I see now... Keep up your good work, and let us know when you finish a working replica of Ruslan setup using all these Tesla mambo-jambo  :o
Good luck !

plaxius

  • Newbie
  • *
  • Posts: 27
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7539 on: December 12, 2014, 12:43:36 AM »
Hi friends .... i buyed two batteries and analog amperemeter. Kacher two copper plates no ground.

24V + 0,8 A
40Watts Bulb mid god brigth ..

https://www.youtube.com/watch?v=4jOYR9HLRuQ


With Rectifier and Power Source


http://youtu.be/E6PgoaUgyb4?list=UUC4ts0Na4PvigP0DHvmj9fg




Bless..

a.king21

  • Hero Member
  • *****
  • Posts: 1650
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7540 on: December 12, 2014, 01:06:23 AM »
Can you have a look at this video and comment on it please. It appears to show a self runner complete with instructions


https://www.youtube.com/watch?v=xNCgPWagn1s

Cap-Z-ro

  • Hero Member
  • *****
  • Posts: 3545
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7541 on: December 12, 2014, 01:36:38 AM »
.

Cap-Z-ro

  • Hero Member
  • *****
  • Posts: 3545
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7542 on: December 12, 2014, 01:38:17 AM »
*posted twice in wrong thread - goes for fresh air*


lost_bro

  • Sr. Member
  • ****
  • Posts: 282
    • youtube channel
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7543 on: December 12, 2014, 03:44:01 AM »
Can you have a look at this video and comment on it please. It appears to show a self runner complete with instructions


https://www.youtube.com/watch?v=xNCgPWagn1s

I find interesting that he states that the signal biasing the coil is composed of two frequences:  50Hz & 1.4KHz..........
Modulated carrier wave???????


take care, peace
lost_bro

John.K1

  • Hero Member
  • *****
  • Posts: 679
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7544 on: December 12, 2014, 11:46:55 AM »
Guys,
https://www.youtube.com/watch?v=ozGwb0glcXg

Kacher, 8V  120mA.  (if true) I really need to work on it.  At that voltage it takes me around 1.2A.

He has two Tesla coils there. Does it look like they are opposite wound? Similar effect has been shown by A.Romanov and If I good remember Don S.  had some set of tesla's coils too.