Storing Cookies (See : http://ec.europa.eu/ipg/basics/legal/cookies/index_en.htm ) help us to bring you our services at overunity.com . If you use this website and our services you declare yourself okay with using cookies .More Infos here:
https://overunity.com/5553/privacy-policy/
If you do not agree with storing cookies, please LEAVE this website now. From the 25th of May 2018, every existing user has to accept the GDPR agreement at first login. If a user is unwilling to accept the GDPR, he should email us and request to erase his account. Many thanks for your understanding

User Menu

Custom Search

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY  (Read 11717907 times)

Void

  • Hero Member
  • *****
  • Posts: 2333
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6330 on: November 01, 2014, 07:58:53 PM »
Here is a shot of my Ruslan replication almost complete build. The scope shot is with the probe just laying on the antenna, which is why the trace is fuzzy. The Kacher was adjusted as close as possible to 1.736MHz with antenna and ferrite choke connected. The length of Kacher secondary coil is 7.5cm. The Kacher primary coil is tapped at about 2.5 turns of the 3 turns to increase secondary voltage which is about 2KV. Current draw is 1.6A.

Nice job Hoppy. What's that yellow 'ribbon' draped over the primary winding of the kacher?
All the best...

John.K1

  • Hero Member
  • *****
  • Posts: 679
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6331 on: November 01, 2014, 08:53:34 PM »
Nice job Hoppy  ;)

Guys, I have removed hell much of the wire fom Tesla secondary to get it resonate at 1.92MHz. When I connect the Tesla directly to he antenna above the bifilar (grenade) coil, a frequency drop very much to 1.3MHz. Why is that?
  That 2 meters of copper tube cant change the frequency as much , or it can?  I didn't connect it via intermediate ferrite bar yet. Could that ferrite coil solve my problem?

Also when Ruslan was talking with the guys on the Skype, he told them this :  1. Make your granade coil   2. Make your Katcher   3. Tune it to correct frequency   4. quick check with 20W bulb on the bifilar- should lit a bit        .....

Did anybody did this pre-test?  What voltage bulb did you choose? It is not working for me even with  12V 21W car bulb.  My Tesla takes 24V @1.2A.

Thank for advice.

Void

  • Hero Member
  • *****
  • Posts: 2333
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6332 on: November 01, 2014, 09:32:18 PM »
Nice job Hoppy  ;)
Guys, I have removed hell much of the wire fom Tesla secondary to get it resonate at 1.92MHz. When I connect the Tesla directly to he antenna above the bifilar (grenade) coil, a frequency drop very much to 1.3MHz. Why is that?
  That 2 meters of copper tube cant change the frequency as much , or it can?  I didn't connect it via intermediate ferrite bar yet. Could that ferrite coil solve my problem?

Hi John.K1. Connecting the 'antenna' coil adds a lot of capacitance to the tesla secondary, 
so it is normal for the frequency to drop a fair bit when you connect anything to the secondary coil.
All the best...


Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6333 on: November 01, 2014, 09:32:32 PM »
Nice job Hoppy. What's that yellow 'ribbon' draped over the primary winding of the kacher?
All the best...

The shot was taken before I had taken the scope shot and I had unwound tape to remove turns from the secondary to adjust frequency.

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6334 on: November 01, 2014, 10:41:08 PM »
My Grenade is resonating at about 1.15MHz (with bifilar coil wound over), so quite close to Itsu's. Is this frequency supposed to match to the Kacha frequency because to get down to yours and my grenade frequency would require a much longer Kacher secondary coil length than Ruslan is showing in his videos, or are we supposed to tune the Kacher to our 'earth' frequency (1.736MHz in Ruslan's case)?

Good question, with my bifilar (Tesla way) in place (18.75m + 2x 0.5m connection in 3 layers (3x 27 turns) measuring 245uH) my Grenade peak
resonance frequency even dropped to 900KHz  :o

With my 0.47uF capacitor in place to connect to the 3 turn yoke secondary, the resonance frequency of this bifilar coil has dropped to 14KHz (was 26 with the old grenade / bifilar).
I had to put 3 of those 0.47uF caps in series (0.15uF) to get back to my earlier 26KHz resonance frequency.

I have the same dim output on my 2 60W/220V bulbs as with the old grenade coil.
 
My Kacher resonates around 1400KHz, so not sure what to do, get it up till 1.7MHz, or down to match the grenade at 0.9MHz

Regards Itsu



   

Void

  • Hero Member
  • *****
  • Posts: 2333
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6335 on: November 01, 2014, 10:53:12 PM »
The shot was taken before I had taken the scope shot and I had unwound tape to remove turns from the secondary to adjust frequency.

Ah, I see. :)
All the best..

stupify12

  • Full Member
  • ***
  • Posts: 175
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6336 on: November 02, 2014, 01:14:07 AM »
Given to your Tesla secondary, the Grenade coils length should be 1/4 of the wavelength as per Tesla stated;

Quote
approximately one-quarter of the wave length of the electrical disturbance in the
secondary circuit based on the velocity of propagation of the electrical disturbance through the coil
itself and the circuit with which it is designed to be used

Now that your frequency drop to 1.3Mhz, the ideal length for the Grenade coil will be 57.69m if there is another way that you can dial up more that frequency then just forget the 57.69meter. What really is important here is the Frequency of Kacher Secondary and  1/4 wavelength of Kacher frequency will be the ideal length for Grenade Coil.

The real wave length to follow here is none other 1/4 wavelength of your working Kacher frequency.

The ground/earth must be Directly connected to one terminal of capacitor, the other terminal of capacitor is connected to the positive output phase. The capacitor here is the most wonderful device which has been implemented to receive and store then convert the Radiant Sun..

Here is the better reference than to speculate and wait for Ruslan to post some detail which he is still uncertain. Figure 2 is your most loved Grenade Coil, which is actually a spire or conical. http://www.teslauniverse.com/nikola-tesla-patents-593,138-electrical-transformer?pq=ZWxlY3RyaWNhbCB0cmFuc2Zvcm1lcg==

Meow

Nice job Hoppy  ;)

Guys, I have removed hell much of the wire fom Tesla secondary to get it resonate at 1.92MHz. When I connect the Tesla directly to he antenna above the bifilar (grenade) coil, a frequency drop very much to 1.3MHz. Why is that?
  That 2 meters of copper tube cant change the frequency as much , or it can?  I didn't connect it via intermediate ferrite bar yet. Could that ferrite coil solve my problem?

Also when Ruslan was talking with the guys on the Skype, he told them this :  1. Make your granade coil   2. Make your Katcher   3. Tune it to correct frequency   4. quick check with 20W bulb on the bifilar- should lit a bit        .....

Did anybody did this pre-test?  What voltage bulb did you choose? It is not working for me even with  12V 21W car bulb.  My Tesla takes 24V @1.2A.

Thank for advice.

magpwr

  • Hero Member
  • *****
  • Posts: 1168
    • Youtube Channel
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6337 on: November 02, 2014, 08:56:10 AM »
hi everyone,

I have just uploaded a youtube video of my
60th SubHarmonics PWM Generator -Part 1
http://www.youtube.com/watch?v=AfOSBGIdORw

This video is about how to find resonance of 1uf capacitor which is connected in series with the 25 turns x 2 on kapanadze coil from the 3 or  4 turns yoke or toroid output.
Much Later stage i will reveal why there is need to multiply the current resonance frequency as shown in video PART 1  by  2 times to comply with 1/2 wave resonance. :)
866.981khz x 2 =1.7339Mhz
14.44khz x 2 =28.88Khz


(Take note i have not added all the decoupling capacitors before and after 1.3mH from center tap of transformer in circuit diagram.I am just using 
1 x bi-directional TVS diode "P6KE20CA"  at gates of IGBT.I have also forgotten to add the "140volts rated varistor in circuit diagram" across Source and Drain of IGBT. :D :D :D :-[ )


Next video Part 2 will be released to show how i easily use a short wire antenna to provide signal to circuit to power the same bulb at same frequency similar to part 1 but only this time
no more signal generator involved.Tesla coil radiate it's frequency and it's perfectly divided by 60 or 60th Sub-harmonics for my PWM generator."No possibility of frequency runaway since it's 100% dependent on tesla coil"

My generator is designed to work up to 3Mhz of radiated frequency.

Pending..
There is also nanosecond generator signal injection which i need to do and show a video,although the circuit was completed weeks back. :'(

----------------------------------
Primary focus is all about circuit since my kapanadze coil is not fully assembled yet while pending purchase of required supporting pvc parts.

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6338 on: November 02, 2014, 11:36:54 AM »
Given to your Tesla secondary, the Grenade coils length should be 1/4 of the wavelength as per Tesla stated;

Now that your frequency drop to 1.3Mhz, the ideal length for the Grenade coil will be 57.69m if there is another way that you can dial up more that frequency then just forget the 57.69meter. What really is important here is the Frequency of Kacher Secondary and  1/4 wavelength of Kacher frequency will be the ideal length for Grenade Coil.

The real wave length to follow here is none other 1/4 wavelength of your working Kacher frequency.

The ground/earth must be Directly connected to one terminal of capacitor, the other terminal of capacitor is connected to the positive output phase. The capacitor here is the most wonderful device which has been implemented to receive and store then convert the Radiant Sun..

Here is the better reference than to speculate and wait for Ruslan to post some detail which he is still uncertain. Figure 2 is your most loved Grenade Coil, which is actually a spire or conical. http://www.teslauniverse.com/nikola-tesla-patents-593,138-electrical-transformer?pq=ZWxlY3RyaWNhbCB0cmFuc2Zvcm1lcg==

Meow



Nice theory Stupify12,

but considering that my Grenade is now 37.5m (x 4 = 150m wavelength = 2MHz), but as shown, it resonates at 1.3MHz, so
this converting wire length directly into resonance frequency is imo only valid for long wire (antenna's), NOT when coiled up.

Now that i have installed my bifilar coil around the Grenade, that same Grenade resonance frequency has even dropped to 900KHz.

Following your theory, i would have to take this 900KHz, take it times 4 = 3.6MHz which would be my Kacher resonance frequency.
This is very high and i doubt it will be reacheable with some degree of power.

Thanks,  regards Itsu


John.K1

  • Hero Member
  • *****
  • Posts: 679
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6339 on: November 02, 2014, 12:07:10 PM »
Ok,  As far as I understand, Tesla and Antena is One.  And that has to be tune to my 1.87MHz  (btw - speed of electrons in coper is 96% of speed of light - technically my frequency to tune to should be 1.85MHz - I keep my tuned tesla/Antena just right below 1.87 allowing for that 4% error which is 20KHz and it is still acceptable. )

Now only my problem is to solve heat on my Kacher's transistor  -probably will need different yoke?   

MenofFather

  • Hero Member
  • *****
  • Posts: 943
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6340 on: November 02, 2014, 12:49:59 PM »
...
Now that i have installed my bifilar coil around the Grenade, that same Grenade resonance frequency has even dropped to 900KHz.
...
Itsu, can you show that scaning picture with 900 kiloherc resonance? And can you scan inductor wounded on granate (better 11 meters lenght, than 18 meters)?

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6341 on: November 02, 2014, 01:02:26 PM »


Nice theory Stupify12,

but considering that my Grenade is now 37.5m (x 4 = 150m wavelength = 2MHz), but as shown, it resonates at 1.3MHz, so
this converting wire length directly into resonance frequency is imo only valid for long wire (antenna's), NOT when coiled up.

Now that i have installed my bifilar coil around the Grenade, that same Grenade resonance frequency has even dropped to 900KHz.

Following your theory, i would have to take this 900KHz, take it times 4 = 3.6MHz which would be my Kacher resonance frequency.
This is very high and i doubt it will be reacheable with some degree of power.

Thanks,  regards Itsu

Itsu & all,

I'm getting the distinct impression that nobody here knows how Ruslan tunes his device to the extent that they can provide a clear step by step guide. Am I wrong?

magpwr

  • Hero Member
  • *****
  • Posts: 1168
    • Youtube Channel
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6342 on: November 02, 2014, 01:32:49 PM »
hi everyone,

60th SubHarmonics PWM Generator -Part 2

http://www.youtube.com/watch?v=0AyBETNxVa0

In this video i reveal that this divide by 60 PWM generator i created was intended to be running wirelessly merely using the radiated frequency of the tesla coil.
I am using rather long antenna -Croc leads for this video.But for actual build using pcb board with proper shielding i will be using shorter antenna placed near tesla coil.

In this part 2 video i have already revealed how easy it is to tune tesla coil resonance frequency from 2.1Mhz to lower frequency by slowly inserting ferrite rods.
There is no need to waste time by rewinding a new tesla coil if the default resonance frequency is above 2Mhz.


The next upcoming video is about nanosecond 50ns...150ns  injection at high voltage at the 3 turns via 1 wire going  through the toroid(providing nanosecond pulse) which can be made to appear either at the positive peak of the lower frequency eg:28khz or appear at the negative peak merely by connecting to one of the 2 outputs from  divide by 60 PWM generator.

"Tips for the day -Patience and alot of planning is needed before actual experiment which does save on unwanted time.Upon actual experiment just execute all the move you have previously made in your head"

MenofFather

  • Hero Member
  • *****
  • Posts: 943
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6343 on: November 02, 2014, 02:11:11 PM »
Itsu & all,

I'm getting the distinct impression that nobody here knows how Ruslan tunes his device to the extent that they can provide a clear step by step guide. Am I wrong?
You not wrong.

Void

  • Hero Member
  • *****
  • Posts: 2333
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6344 on: November 02, 2014, 03:49:47 PM »
I'm getting the distinct impression that nobody here knows how Ruslan tunes his device to the extent that they can provide a clear step by step guide. Am I wrong?

Hi Hoppy. I have pointed this out a few times over the last few weeks. :)  This little fact apparently doesn't stop
many people from posting here and telling everyone exactly what they should be doing to get overunity, even though
these same people do not have a self running device.  ;D
The ego is a strange animal. ;)

Don't be discouraged. Keep experimenting to try to understand what makes these devices tick.
This is what I have been focusing on. I am seeing some interesting things, but I still need to
do a lot more experimenting yet. Problem is I am very busy lately so not a lot of free time right now. :)
All the best...