Storing Cookies (See : http://ec.europa.eu/ipg/basics/legal/cookies/index_en.htm ) help us to bring you our services at overunity.com . If you use this website and our services you declare yourself okay with using cookies .More Infos here:
https://overunity.com/5553/privacy-policy/
If you do not agree with storing cookies, please LEAVE this website now. From the 25th of May 2018, every existing user has to accept the GDPR agreement at first login. If a user is unwilling to accept the GDPR, he should email us and request to erase his account. Many thanks for your understanding

User Menu

Custom Search

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY  (Read 11717899 times)

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5475 on: October 02, 2014, 11:52:57 AM »
There is an interesting shot in the following video from Ruslan where he shows a nano pulser circuit in a box on the floor which looks as if its been chopped out of a previous build: -

https://www.youtube.com/watch?v=iyDaVspeeNE


Jeg

  • Hero Member
  • *****
  • Posts: 1532
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5476 on: October 02, 2014, 12:20:00 PM »

@ Jeg, thanks for the main coil wire length (32 meters), not sure why its important as any wavelength/resonance
calculations are skewed in a coil compared to the full length wire.



It is not so important when you already know the 5cm ruslan's diameter and his low freq. But if you start from nothing you need some references to unfold your design calculations.

d3x0r

  • Hero Member
  • *****
  • Posts: 1433
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5477 on: October 02, 2014, 12:43:36 PM »
re: http://www.overunity.com/12736/kapanadze-cousin-dally-free-energy/msg417615/#msg417615


the TK (not to be confused with T(insel)K) coil,  has a variety of resonant frequencies...
the resonant primary ( 17-27-37 Khz something ) should be relative to one of these?
Should the kacher be relative to a different one? 


I also have a good resonant point at 500Khz give or take a bit.. I added a few turns to the primary so the measured inductances are 260uH and 260uH hoping to get a good coupling with a capacitor on the primary. 


The most voltage I get out is at this 500Khz, that takes 5vpp to 48vpp...


I guess this is from the ferrite coil that's added now...


@itsu can also test resonances with just a signal generator at the ferrite input
I think you'll need a tunable delay between when the 494 goes on and the impulse happens...

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5478 on: October 02, 2014, 01:17:06 PM »

@itsu can also test resonances with just a signal generator at the ferrite input
I think you'll need a tunable delay between when the 494 goes on and the impulse happens...

Hmmm, i do not know what you mean as i have no ferrite in use yet (just winding the yoke now, do you mean that?)

"a tunable delay" yes i guess so, that would be a challenge for me to build.

Regards Itsu

d3x0r

  • Hero Member
  • *****
  • Posts: 1433
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5479 on: October 02, 2014, 01:43:52 PM »
Hmmm, i do not know what you mean as i have no ferrite in use yet (just winding the yoke now, do you mean that?)

"a tunable delay" yes i guess so, that would be a challenge for me to build.

Regards Itsu


no actually I was originally thinking of testing just the coil... but I recently added a ferrite core (yes the yoke) but can test the other resonances without the core...
was just thinking though that I didn't previously have this other 500k frequency


the tunable delay was the 7400 things dally used.... it's also kinda what the 7414/7400 module does...

Jeg

  • Hero Member
  • *****
  • Posts: 1532
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5480 on: October 02, 2014, 02:15:14 PM »
Hi guyz,

Take a look. 
This is what I have and another from 115V / 230V ac to 12V 5amps .

Enjoy

Hi GF
Is it possible to ask the fellow researchers at realstrunic.com what is their opinion about the input frequency of this supply module? Our team here have many objections as you saw about that. At least to prepare myself for modifications as i already ordered it and it is on the way home.

An other question again on the same matter. In case that this KHz range frequency is not the appropriate for supplying this module. Is there any way for transforming those 24V output to 50Hz dc pulses? Perhaps with an electronic switch and a simple RC??? 

magpwr

  • Hero Member
  • *****
  • Posts: 1168
    • Youtube Channel
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5481 on: October 02, 2014, 02:31:12 PM »

no actually I was originally thinking of testing just the coil... but I recently added a ferrite core (yes the yoke) but can test the other resonances without the core...
was just thinking though that I didn't previously have this other 500k frequency


the tunable delay was the 7400 things dally used.... it's also kinda what the 7414/7400 module does...

hi d3x0r,

The Dally nanopulser was already tested in the virtual environment after i have completed fixing the Akula nanopulser section which was uploaded previously.

I can tell you the Dally nanopulser doesn't even work using HC or HCT for the 1st I/C to the 1st I/C to the left without even completing the circuit at 2nd I/C."This circuit is also riddled with intentionally created bug"

Please don't waste time on obsolete nano-pulser circuit which is also not design to work in sync it was meant to work as standalone.

----------------------------------------------

I started pondering on Nikola Telsa reference to "the knife" that he created base on old interview ,right away it reminded me of the nano-pulse which is shaped like a knife which the sharp edge of knife is facing up. :D   

Old name for nano-pulse is "knife"."This nano second generator word did not exist during Nikola time although he have used this "knife" for his device.Please read interview once more if needed where this knife is mentioned"   "Please don't ponder over this part too seriously" :)

I will explain more findings on yoke and maybe 1/2 wave 18.75meter  later ,since i just got home. :)

"The human mind can be walking laboratory which allows you to plan all the possible combination if you are good at visualizing circuit or etc in your head to understand the flow to a certain extend before even commencing any actual experiment in order to save time"


If anyone still says kapanadze replication is so simple that you will laugh just by looking at the circuit,please think wisely once again-
In short there are layers upon layer upon layer upon layer of waveform\nanopulser\frequency which needs to be in sync with coil and etc.

 
We are now very close just 2 more section i need to talk about- yoke and 1/2 wave to continue from the latest information some of us have acquired through this topic and hopefully digested at the same time.
"Memory plays a very important role here or just take down notes on the pointers if keen on replication"
 

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5482 on: October 02, 2014, 03:17:11 PM »

If anyone still says kapanadze replication is so simple that you will laugh just by looking at the circuit,please think wisely once again-
In short there are layers upon layer upon layer upon layer of waveform\nanopulser\frequency which needs to be in sync with coil and etc.

 

How do you know this for certain in relation to kapanadze's devices?

magpwr

  • Hero Member
  • *****
  • Posts: 1168
    • Youtube Channel
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5483 on: October 02, 2014, 03:36:21 PM »
How do you know this for certain in relation to kapanadze's devices?

hi Hoppy,

Please do not waste my time by asking by using the word "certain" any more.

I have hinted previously and i shall enlighten you once again "i am using only instinct and applying my reverse engineering skills" .This is not to be confused with gut feeling.

For what i know this forum was dead before.I was not even keen to replicate there was alot of missing information since this topic or the another was started few years ago.

Long story short i am just assisting just those whom are "not skeptic to be in this topic" to replicate the device but only after understanding all the basic fundamental to somehow get this device into self sustaining state.

I am living in Asia waiting for components to arrive to me is like waiting for the coffin to be built."The waiting time is killing me so i decided to assist for this topic in the meantime"

I shall not waste any more time by getting involved in unwanted discussion only unless the experiment conducted did not tally with my findings,hopefully will not happen. :D :D :D :D

The old and new Kapanadze topic valuable time was wasted because of unwanted discussion for the last few years.I am here to change that if you don't mind.I hope you won't take this the wrong way.

"I work with no emotions or feelings but just using pure logical thinking all the way."

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5484 on: October 02, 2014, 05:06:50 PM »
hi Hoppy,

Please do not waste my time by asking by using the word "certain" any more.

I have hinted previously and i shall enlighten you once again "i am using only instinct and applying my reverse engineering skills" .This is not to be confused with gut feeling.

For what i know this forum was dead before.I was not even keen to replicate there was alot of missing information since this topic or the another was started few years ago.

Long story short i am just assisting just those whom are "not skeptic to be in this topic" to replicate the device but only after understanding all the basic fundamental to somehow get this device into self sustaining state.

I am living in Asia waiting for components to arrive to me is like waiting for the coffin to be built."The waiting time is killing me so i decided to assist for this topic in the meantime"

I shall not waste any more time by getting involved in unwanted discussion only unless the experiment conducted did not tally with my findings,hopefully will not happen. :D :D :D :D

The old and new Kapanadze topic valuable time was wasted because of unwanted discussion for the last few years.I am here to change that if you don't mind.I hope you won't take this the wrong way.

"I work with no emotions or feelings but just using pure logical thinking all the way."


Hi Magpwr,

With respect, you can only reverse engineer a device if you have the device. I asked you a reasonable question that you appear to have taken offense at. You have answered in many words indicating that you are not certain and that your statement is your opinion based on your thought process. That's fine, thank you. In future, I will remember to add an imaginary 'IMO' into your statements about other peoples devices that are highlighted and written as factual. I hope you will not take this the wrong way.

Needless to say, I am a skeptic but not a skeptic that simply sits on their arse typing thoughts into a keyboard. I am a hands-on experimenter like yourself and take notice of comments from other experimenters who are in the process of attempting replications. I attempted a replication of the Dally device at the start of this thread and today started building the Ruslan Yoke. I intend to carry on building the rest of the Ruslan device based on my understanding of all that I have read and seen on the subject.

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5485 on: October 02, 2014, 07:28:54 PM »
  Well, I'm very glad to see both Hoppy and Itsu getting into this project. Now that we have a bit more information on these devices.
  It wouldn't hurt for Geo to show the way, if he's into it.
 
    While both Akula and Ruslan are working overtime to complete new projects, it's hard for us to keep up with all their new improvements. As each device is more complicated than the previous one, which we haven't figure out, yet.
 
   What I'd like to see is a working barebones model that we can all replicate, that WORKS. Also a proven working schematic, videos, and explanations on turning, etz...    Barebones, for dummies, like me...

  I'm having a hard time dealing with a problem with the induction part of the crt. The device turns on, but the lights and power fail after a few seconds. Might be bad fets, as I've gone through 4 of the IRFP260N, and possibly have another one that might be failing now.
 Anyways, I'll figure it out, sometime. But, that's what hanging me up right now.

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5486 on: October 02, 2014, 07:42:24 PM »
  Can anyone answer this question?
  Does the newer or newest Ruslan device have a separate nanosecond circuit to control the Kacher output? As all I see is the Kacher crt without any additional modulator.
  If not, then this is an important point, as it simplifies the Kacher part of the crt, as only one modulator crt would be needed for the induction part of the crt.  OR not?

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5487 on: October 02, 2014, 10:39:31 PM »

  I'm having a hard time dealing with a problem with the induction part of the crt. The device turns on, but the lights and power fail after a few seconds. Might be bad fets, as I've gone through 4 of the IRFP260N, and possibly have another one that might be failing now.
 Anyways, I'll figure it out, sometime. But, that's what hanging me up right now.

Nick,
Please describe your present circuit setup and show a close-up of your mosfets and associated components, so that we can try to help solve your problem.

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5488 on: October 03, 2014, 12:03:14 AM »

I finished my yoke windings and can start to hook it up to the MOSFET's and coils.
Its all 2.5mm² solid copper wire and all CW.


I lost some time because i received my 7414/7400 chips and expanded the breadboard with this 7414/7400 circuit to see if
i could use it lateron for tuning my nano pulser to the 27KHz sine wave.

I notice that the signals as can  be seen on the original Ruslan diagram (screenshot 1) are not replicateable by me (screenshot 2).

I used the unmodified diagram, so no changes like suggested by MAGPWR up till now, but one...., the non-inverting ucc37322 MOSFET driver instead of
the inverting ucc37321 MOSFET driver used in the diagram, simply because i only had the non-inverting ones and i thought it would not matter.

But as can be seen, the red trace from the diagram has a 60% ontime versus 40% offtime, while my yellow trace is the other way around.
Probably because of this i cannot adjust my blue and purple traces as the blue and green traces on the diagram
 
So any suggestions are welcome what is causing this, and if i should order some inverting ucc37321's or if there is another solution or problem to solve.


Video here:    https://www.youtube.com/watch?v=-6jKC-XTDFQ&feature=youtu.be

Regards itsu

magpwr

  • Hero Member
  • *****
  • Posts: 1168
    • Youtube Channel
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #5489 on: October 03, 2014, 12:38:55 AM »
I finished my yoke windings and can start to hook it up to the MOSFET's and coils.
Its all 2.5mm² solid copper wire and all CW.


I lost some time because i received my 7414/7400 chips and expanded the breadboard with this 7414/7400 circuit to see if
i could use it lateron for tuning my nano pulser to the 27KHz sine wave.

I notice that the signals as can  be seen on the original Ruslan diagram (screenshot 1) are not replicateable by me (screenshot 2).

I used the unmodified diagram, so no changes like suggested by MAGPWR up till now, but one...., the non-inverting ucc37322 MOSFET driver instead of
the inverting ucc37321 MOSFET driver used in the diagram, simply because i only had the non-inverting ones and i thought it would not matter.

But as can be seen, the red trace from the diagram has a 60% ontime versus 40% offtime, while my yellow trace is the other way around.
Probably because of this i cannot adjust my blue and purple traces as the blue and green traces on the diagram
 
So any suggestions are welcome what is causing this, and if i should order some inverting ucc37321's or if there is another solution or problem to solve.


Video here:    https://www.youtube.com/watch?v=-6jKC-XTDFQ&feature=youtu.be

Regards itsu

hi itsu,

Please refer to my ver 4.0 fixed circuit diagram as attached.There are around 7 bugs i have detected in the "unmodified circuit diagram which you were referring from".Please refer to my modified circuit ver 4.0.I have previously pasted the waveform in there expand attached image to 150% ...200% and look to the bottom right where i have linked where are all the 4 waveform obtaining from.

On the surface it looks like a working 3-phase generator which derive it's signal from TL494."But this is true on the surface but it is actually a nano second generator.Please see my advise below"

The top potentiometer 22kohms control the position of the waveform "C" little to the left or right.

The bottom potentiometer 22kohms control duty cylcle of the waveform "C" .

Look at the comment which have pasted to the left of  the 74HC00 22kohms potentiometer.This potentiometer value of 22kohms needs to be changed to 1kohms in order to convert this circuit into a nanosecon generator which resemble Ruslan drawing or inverted knife shape. :)

I have also mentioned in circuit diagram that both I/C:7400 and 7414 needs to be replaced with 74HC00 and 74HC14.

I have also attached the video of this nanosecond generator with the ver 4.0 fix(Final fix).Please do refer to this mp4 video of virtual circuit simulation which i have attached previously as well(Final version).

Lastly the nanosecond generator section needs to be connected to one of the 2 output from TL494 (Channel A or B).Please ensure the logic level at point "A" in nanosecond generator is high enough in virtual this displayed as 4volts(please look at the waveform which i have pasted to the right side of the circuit with volts/div indicated.