Author Topic: Kapanadze Cousin - DALLY FREE ENERGY (Read 11804008 times)

Jeg · « **Reply #22545 on:** October 09, 2020, 05:01:17 PM »

AG
Yes i understand. I make this all time. Cycles over cycles. But each time we learn more and more from our mistakes. Don't we?

Jeg · « **Reply #22546 on:** October 09, 2020, 08:26:42 PM »

Quote from: NickZ on October 09, 2020, 04:36:59 PM

Jeg: That was the HF/HV kacher signal, as read by the HV scope probe, with no negative ground probes attached, at round 900KHz, or so. The point being was to tune the HV/HF signal and frequency to interact with the induction circuits. As you can see in the video, there is some interaction, but not enough, at that time. Yet it can partially light 3 200w bulbs.
However, I see no improvements over that output, by the other shown controlable kacher circuits, as yet. And so I've been waiting for you or apecore or Geo, to show me how well your controlable circuit works to self run. And, I'm still waiting...
NickZ

Hi Nick
Thanks for explaining.
I have dissmantled mine, when i had realized the dead end of building something without understanding it. Very counter productive method.

You can sync your kacher easily when you need it anyway...

AlienGrey · « **Reply #22547 on:** October 09, 2020, 08:52:51 PM »

Quote from: Jeg on October 09, 2020, 05:01:17 PM

AG
Yes i understand. I make this all time. Cycles over cycles. But each time we learn more and more from our mistakes. Don't we?

Hi Jeg we were i bit busy earlier sorry

Thanks for the video I haven't seen that one there is also this shot I found on one of the forums, along with no other data.

Jeg · « **Reply #22548 on:** October 10, 2020, 07:42:09 AM »

Quote from: AlienGrey on October 09, 2020, 08:52:51 PM

Hi Jeg we were i bit busy earlier sorry

Thanks for the video I haven't seen that one there is also this shot I found on one of the forums, along with no other data.

Hi AG.
Yes it seems that one of the OU techniques is there. HV-Modulation-demodulation-LC tank current rising. At least if someone takes it in account, he might has chances to adjust the circuit for doing that.

NickZ · « **Reply #22549 on:** October 10, 2020, 03:07:26 PM »

Quote from: Jeg on October 09, 2020, 08:26:42 PM

Hi Nick
Thanks for explaining.
I have dissmantled mine, when i had realized the dead end of building something without understanding it. Very counter productive method.

You can sync your kacher easily when you need it anyway...

Jeg:
Yeah, I figure that you had taken yours apart. Well, mine is still together, and waiting for the missing link.
Akula understands it, but he can't get it going in Germany, or Latvia.
It can take me a couple of days sometimes, to "sync" the Kacher, partially, and still without OU. You see how touchy it is.

So then, which device do you understand beforehand? Most of these little devices are nothing but a toy, or flashlight at best. I would really like to have a real one... that lights my house, etz...

AlienGrey · « **Reply #22550 on:** October 10, 2020, 11:11:55 PM »

Quote from: NickZ on October 10, 2020, 03:07:26 PM

Jeg:
Yeah, I figure that you had taken yours apart. Well, mine is still together, and waiting for the missing link.
Akula understands it, but he can't get it going in Germany, or Latvia.
It can take me a couple of days sometimes, to "sync" the Kacher, partially, and still without OU. You see how touchy it is.

So then, which device do you understand beforehand? Most of these little devices are nothing but a toy, or flashlight at best. I would really like to have a real one... that lights my house, etz...

Nick are you saying you have built this thing but you don't have the foggiest idea how it is suppose to work ?
and we thought you had all the answers ?

soliman · « **Reply #22551 on:** October 11, 2020, 04:07:21 AM »

Hello,
I think here that many people are partially believing that they have something,
this seems to be real, but it is not.
an example of something that happened to me.
remember that when you. turn on the kacher there is radiation.
This radiation affects the push pull and partially produces some power.
But, this is a mistake.
You have to pre-protect from interference your circuit.
With an oscilloscope look at the square waves of TL494 pin 9 and 10.
These must be totally free of noise.
if you. see noise here, or a random signal, this means that you.
has been a victim of radiation interference from the kacher.
Avoid this, use a metal cover for your circuit or move it far enough away to avoid
that undesirable interference from the kacher on the push pull.

Blessings.

conico · « **Reply #22552 on:** October 11, 2020, 05:35:09 AM »

You're right Soliman.
You can see with the oscilloscope on mosfets gates. You don't suplly push-pull, supllay just Katcher. You will see on the oscilloscope that it is a 4-5v signal on the gates of mosfets from Katcher.

sometimes I have this push-pull signal from Katcher, sometimes I don't have it.

conico · « **Reply #22553 on:** October 11, 2020, 06:11:38 AM »

I found a document with explanations of Ruslan. The length of the ground wire is the same as the length of the secondary Tesla.
I can't attach the document.

AlienGrey · « **Reply #22554 on:** October 11, 2020, 12:18:15 PM »

Quote from: NickZ on October 10, 2020, 03:07:26 PM

Jeg:
Yeah, I figure that you had taken yours apart. Well, mine is still together, and waiting for the missing link.
Akula understands it, but he can't get it going in Germany, or Latvia.
It can take me a couple of days sometimes, to "sync" the Kacher, partially, and still without OU. You see how touchy it is.

So then, which device do you understand beforehand? Most of these little devices are nothing but a toy, or flashlight at best. I would really like to have a real one... that lights my house, etz...

Nick on reading some of your earlier posts you quot Sergey Storkers work, Personally I find it a little confusing
the reason why is if you LISTEN to his clips on youtube. his video's he specify a tube no less than 50mm.

Unless you stick! to his video's your missing out! Its about MUSIK resonant frequency but you still might not get it it's
he is a Russian speaker! he says he uses a de tuned 44M not 37 or Nazi 40m
it's actually has to add up to 9 the universe the flower of LIFE It's lasered into the Egyptian temple at abidos!

AG

conico · « **Reply #22555 on:** October 11, 2020, 01:58:56 PM »

Information from Ruslan how to find the working frequency of push-pull.

conico · « **Reply #22556 on:** October 11, 2020, 04:10:04 PM »

I followed Ruslan's instructions and put on the 10 meter Inductor the function generator and on the grenade coil oscilloscope probe. The maximum amplitude was at 1690-1710 Khz but the signal did not dance in amplitude. At 1742Khz he began to dance. On 1750Khz the oscilloscope show me a wave like a fish. If i changed frequency at 1751Khz or 1749Khz the wave like a fish disappear.

I moved on with frequency and found at 1850Khz a wave that danced louder in amplitude. I changed the time base of the oscilloscope and found the fish wave. Changing only by 1 Hz frequency, the fish wave disappears

in my case the push-pull frequency can be 1750Khz: 50 = 35Khz or 1850: 50 = 37Khz

NickZ · « **Reply #22557 on:** October 11, 2020, 05:10:34 PM »

Deleted.

conico · « **Reply #22558 on:** October 11, 2020, 07:42:19 PM »

NickZ, what I've posted so far isn't for you because you don't believe me and you don't believe Ruslan anyway.
I'll show you what your misconceptions are.
I have a maximum amplitude at 1.8Mhz and you tel me i must use 15-18 Khz in Push-Pull. In Push-pull I must use an harmonic of 1.8Mhz, that mins 50th or 60th or 90th harmonic at list 1800: 90=20Khz. If I use 15Khz as you said, that is 123Th harmonic.
I've never heard of the 123 harmonica, no one uses that.
Second mistake is the groud wire of 37.5m. Grenade coil have 37.5m but it is not connected directly to ground, it is in series with 28turns , another 5 meters of wire on Yoke.

AlienGrey · « **Reply #22559 on:** October 11, 2020, 08:40:10 PM »

Quote from: NickZ on October 11, 2020, 05:10:34 PM

conico: None of your three frequency points are even close to what they should be for the Push-Pull circuit, 15KHz, or so.
If the rest of your set up is up to specs, including the proper 2000v frequency tuning caps, then, the push pull frequency should be found somewhere between 15KHZ, and 18KHz. And, the Kacher's corresponding best frequency sync point between about 1.5 to 1.9MHz. Those are the number that you should be aiming for, and not 37KHz.
The Earth ground line should match the grenade coil in size. 37.5 to 40 meters long. Not 5 or 10 or 20, nor any other size.
I am not trying to reinvent the wheel, nor do I think that I know better. I just try to follow the provided schematics, and instructions. However, one tiny difference can make all the difference at the output, one way or the other.
I don't need to know how this device is "supposed" to work. I am an electronic assembler, and so, I can build it, but I can't design it. Therefore, the design and schematic have to be right in the first place. Or we'll just be replicating some one else's errors.
Perhaps, that is what THEY want... and we have not disappointed THEM.

NickZ

Does this help ?

News:

User Menu

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY (Read 11804008 times)

Jeg

Re: Kapanadze Cousin - DALLY FREE ENERGY

Jeg

Re: Kapanadze Cousin - DALLY FREE ENERGY

AlienGrey

Re: Kapanadze Cousin - DALLY FREE ENERGY

Jeg

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY

AlienGrey

Re: Kapanadze Cousin - DALLY FREE ENERGY

soliman

Re: Kapanadze Cousin - DALLY FREE ENERGY

conico

Re: Kapanadze Cousin - DALLY FREE ENERGY

conico

Re: Kapanadze Cousin - DALLY FREE ENERGY

AlienGrey

Re: Kapanadze Cousin - DALLY FREE ENERGY

conico

Re: Kapanadze Cousin - DALLY FREE ENERGY

conico

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY

conico

Re: Kapanadze Cousin - DALLY FREE ENERGY

AlienGrey

Re: Kapanadze Cousin - DALLY FREE ENERGY