Storing Cookies (See : http://ec.europa.eu/ipg/basics/legal/cookies/index_en.htm ) help us to bring you our services at overunity.com . If you use this website and our services you declare yourself okay with using cookies .More Infos here:
https://overunity.com/5553/privacy-policy/
If you do not agree with storing cookies, please LEAVE this website now. From the 25th of May 2018, every existing user has to accept the GDPR agreement at first login. If a user is unwilling to accept the GDPR, he should email us and request to erase his account. Many thanks for your understanding

User Menu

Custom Search

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY  (Read 11688135 times)

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #20850 on: March 14, 2019, 05:04:03 PM »
High frequency diodes have low efficiency and large losses at equivalent noise spectrum above megahertz.
There is a special POWER HF  arsenide-gallium diodes, but such diodes are not sold on the market, or are very expensive.
 In addition, it is necessary to match the source and load impedances. Usually this makes a special transformer.
Probably a suitable chip for measuring energy of chaotic pulses, but not high frequency:https://www.analog.com/media/en/technical-documentation/data-sheets/2947fa.pdf

   Sergh:
   If you are talking about the diodes used on the full diode bridge at the grenade's output, I used the U1560 high speed diodes, which don't get hot like some others do. There is a lot of power going through those diodes, and if the right diode is not used, the rectified voltage at the output will be lower, and any improper diodes will burn up. The U1560 do fine, without heating up, but the U1560 are higher voltage ones, and are better yet. So, the U1560 are the ones that I would recommended.

AlienGrey

  • Hero Member
  • *****
  • Posts: 3713
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #20851 on: March 14, 2019, 07:35:05 PM »
U1560 U = Ultra fast 60 ns (35), 15 = 15 amp 60 = 600v

the low forward voltage drop Average now you can get 1200v Ultrafast
but I'm sure Surgh can quote some better avalanche types  :D

Watch  https://www.youtube.com/watch?v=2xBkukmZ1Oo

Sergh

  • Hero Member
  • *****
  • Posts: 581
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #20852 on: March 14, 2019, 09:16:28 PM »
As with all modulated signal frequency RF needs demodulating down to a more usable frequency by heterodyning !!
only a reprobate/novice would try rectifying or using UHF RF as is as a power sauce directly and ignore phase shifting etc.
As I'm sure it's a puzzle where Mr. Henry T  Morey and others like D Smith obtained his devices you refer to from.
It is used mainly because it is easier to amplify a lower frequency narrowband signal.
In addition, a mixer is required. A mixer is a non-linear element for mixing frequencies.
Without it, the frequencies will not mix. The mixer is made with diodes or transistors. Again the diodes...
https://en.wikipedia.org/wiki/Heterodyne

   Sergh:
   If you are talking about the diodes used on the full diode bridge at the grenade's output, I used the U1560 high speed diodes, which don't get hot like some others do. There is a lot of power going through those diodes, and if the right diode is not used, the rectified voltage at the output will be lower, and any improper diodes will burn up. The U1560 do fine, without heating up, but the U1560 are higher voltage ones, and are better yet. So, the U1560 are the ones that I would recommended.
This diode has a reverse recovery time of 60 ns. But I think that it is inefficient to use it as a power rectifier above 100 - 200 kHz due to the transition capacity. Diodes with a reverse recovery time of 18 ns, HFA08TA60CPBF,  as power rectifiers <1 MHz. But super-fast diodes do not quite match the power diodes due to the higher forward voltage  at maximum current. Above 1 MHz, as power rectifiers, Schottky diodes are mainly used for not too big currents and low voltages. Or new SiC Schottky Diodes.
https://en.wikipedia.org/wiki/Schottky_diode


What do you think about such rare gallium arsenide power diodes from the Soviet Union times?
225 volts, 1 amp, 20 picofarads, reverse recovery 100 picoseconds (0.1 ns ), working frequency of rectification up to 1 GHz :
http://www.155la3.ru/3d713a.htm
Probably have similar Western diodes. I have no idea where such power diodes could be used in ordinary electronics ..

What is the point of rectifying high-frequency voltage? Bulbs glow at high frequency as well as at low. The heat is the same. Only for powering the device itself?

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #20853 on: March 15, 2019, 02:54:43 PM »
   Sergh:   The point is that in order to have a use able feed back circuit, in order to self run, and not just light some bulbs, those diodes are used by me to rectify the HV and HV to be acceptable as an input source to the 24v power supply, which is the feed back circuit PS going back to the input.
   I am not trying to reinvent the circuit, and these diodes work for me.  You can chose what ever diodes that you think work better. Or no diodes or rectifier at all, if you think that that would be better, yet.
   I try follow the schematic, which shows the 12R06 are the normally recommended diodes for that purpose, but the 1560 diode should work just as well up to the needed 2MHz. My Kacher runs at around 1MHz, and my induction circuit runs at around 1.5KHz. And the 1530 diodes seam to do the job to rectify the needed voltages and currents, without heating up.

AlienGrey

  • Hero Member
  • *****
  • Posts: 3713
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #20854 on: March 15, 2019, 09:53:30 PM »
Anyway, if your really stuck you can wire up any MOSFET as any fast diode or MOSFET can operate  with any of the mos fets original limits !    so there.

Nickz  My Kacher runs at around 1MHz, and my induction circuit runs at around 1.5KHz. And the 1530 diodes seam to do the job to rectify the needed voltages and currents, without heating up.
 
'Can you get your Katcher up to 1.5mhz' it would then be a lot happier if your induction winding was 15khz

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #20855 on: March 16, 2019, 02:43:52 AM »
    AG:  Ya well.... That's what you always seam to think. That these matched frequencies are going to line up perfectly. They don't.
    Can you produce something out of all those good thoughts and ideas that you've read about, that you think is the way to go, but haven't shown anything actually working? So, why don't you try to match those frequencies as you think should be, and show us how well it goes.
     What I'm suggesting has been tested, already, concerning the diodes in the previous post. And, I know what I need to do as a next step in the process. 
     No need for armchair suggestions that have not been tried, first. But, thanks anyway.
   

   BTW: My Kacher has no problem running at 1.5MHz, but it works BEST at around 1MHz, as far as what it does to the induction circuit and it's coils, which can be seen at the output of the bulbs. 

conico

  • Sr. Member
  • ****
  • Posts: 292
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #20856 on: March 16, 2019, 06:41:41 AM »
A G. , an advice on the Russian forums, uses only the harmonics multiples of 3, that is 30th, 60th, 90th, in your case may be 90th.
 
I have two more pictures taken from the forums, I do not remember which forum,
these pictures reveal the secret of how to tune Ruslan devices.
I found these pictures yesterday on my computer but they were two years old.

conico

  • Sr. Member
  • ****
  • Posts: 292
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #20857 on: March 16, 2019, 07:16:40 AM »
A.G, There is nothing wrong with Sergey's movie.
In the first part of the film, he sees that his spectrum analyzer says something is wrong, Sergey saw that and at 9.47 in the movie he saw that, he had changed his tesla coil secondary. After that he didn't use Sp Analyzer.
An information on Sergey movie is his secondary tesla coil is 37.5 m long wire, 1 mm diameter.

AlienGrey

  • Hero Member
  • *****
  • Posts: 3713
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #20858 on: March 16, 2019, 09:21:57 AM »
A.G, There is nothing wrong with Sergey's movie.
In the first part of the film, he sees that his spectrum analyzer says something is wrong, Sergey saw that and at 9.47 in the movie, he saw that he had changed his Tesla coil secondary. After that, he didn't use Sp Analyzer.
Information on Sergey movie is his secondary tesla coil is 37.5 m long wire, 1 mm diameter.
Hi there Conico I didn't say there was, did I? the only problems I have has so far is one of the other circuits
where the 1.5mhz Nand gate is fed into the buffer UCC37322 it loads it and I get nothing luckily though there is a spare buffer
I used and changed the UCC37322 to a 37321.
Another problem I had while testing was locking the 1.5Mhz to the 15khz signal but after a lot of trouble building some logic
I found the Scope a Rigel DS1054 is not too accurate on frequency so be aware.
I too had to rewind my Katcher to match up wire length lambda for resonance matching in order to get peek amplitude at 1.5 and 15khz! on my test rig.

Sergh

  • Hero Member
  • *****
  • Posts: 581
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #20859 on: March 16, 2019, 09:40:30 AM »
My Kacher has no problem running at 1.5MHz, but it works BEST at around 1MHz, as far as what it does to the induction circuit and it's coils, which can be seen at the output of the bulbs.
Very simple, like “Kacher”, circuit for a higher frequency. ;D
In the circuit used a special radio frequency, but cheap transistor.
https://www.youtube.com/watch?v=BGgIrkNfa7U

On YouTube you can find a lot of similar instructions for building such a "Kacher" .

Jeg

  • Hero Member
  • *****
  • Posts: 1532
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #20860 on: March 16, 2019, 09:50:58 AM »
Hi all
Guys. Is there anyone here that have seen this video about acula's 494 circuit? At 10:17 he shows a waveform that i really can't understand how the heck he made it. Look all those high frequency peaks. I could replicate this waveform with other means i guess, but it is interesting to see how Acula made it by using a 494. Same waveform could be across our push-pull's drains. Any idea on this?

https://www.youtube.com/watch?v=0bBTqA6opUY

Looks like he set his 494 output at high frequency but somehow he modulates it with a lower frequency component.

Void

  • Hero Member
  • *****
  • Posts: 2333
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #20861 on: March 16, 2019, 10:23:16 AM »
Hi all
Guys. Is there anyone here that have seen this video about acula's 494 circuit? At 10:17 he shows a waveform that i really can't understand how the heck he made it. Look all those high frequency peaks. I could replicate this waveform with other means i guess, but it is interesting how Acula made it by using a 494. Same waveform could be across our push-pull's drains. Any idea on this?
https://www.youtube.com/watch?v=0bBTqA6opUY
Looks like he set his 494 output at high frequency but somehow he modulates it with a lower frequency component.

Hi Jeg,
Edit: Or maybe that guy has a mistake in his circuit layout?

Akula is very good at circuit design, and many of the schematics which he supposedly
created can be a bit hard to follow sometimes. :) Some of the Akula schematics posted did not seem to match exactly
what Akula was doing in his actual demos sometimes, as well. In at least some of Akula's supposed self running LED driver circuits,
he seems to have wound the ferrite transformer in a special way using a copper foil to wrap around the ferrite core before continuing
on with the coil made of magnet wire. That seems to possibly have been an important feature in at least some of
Akula's claimed self running LED circuits.


r2fpl

  • Hero Member
  • *****
  • Posts: 744
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #20862 on: March 16, 2019, 10:26:20 AM »
A G. , an advice on the Russian forums, uses only the harmonics multiples of 3, that is 30th, 60th, 90th, in your case may be 90th.
 
I have two more pictures taken from the forums, I do not remember which forum,
these pictures reveal the secret of how to tune Ruslan devices.
I found these pictures yesterday on my computer but they were two years old.

I think that there is no explanation. Each resonance works on the second resonance as the second harmonic works on successive harmonics but it is always the same problem - LENZ.
Why should it be different in this case?
Everything is beautiful until LOAD.

Harmonics always work in opposition and no matter how far they are 2..10.100th

AlienGrey

  • Hero Member
  • *****
  • Posts: 3713
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #20863 on: March 16, 2019, 10:27:32 AM »
Hi all
Guys. Is there anyone here that have seen this video about acula's 494 circuit? At 10:17 he shows a waveform that i really can't understand how the heck he made it. Look all those high frequency peaks. I could replicate this waveform with other means i guess, but it is interesting to see how Acula made it by using a 494. Same waveform could be across our push-pull's drains. Any idea on this?

https://www.youtube.com/watch?v=0bBTqA6opUY

Looks like he set his 494 output at high frequency but somehow he modulates it with a lower frequency component.
it's not Akula and does noy sound like him, and if you put the guy on trans late he is talking about 'junk' globally gook!

AlienGrey

  • Hero Member
  • *****
  • Posts: 3713
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #20864 on: March 16, 2019, 10:28:00 AM »
it's not Akula and does not sound like him, and if you put the guy on trans late he is talking about 'junk' globally gook!