What happened to NickZ ?
So many N words here lately and not a pip from Nick.  I am worried about him...

Hi T-1000. Thanks for posting more info from Akula.
It is not clear to me however what Akula actually stated and what you
may have added onto that in your statement above. Did Akula specifically say that he thought
it was NMR or similar that was causing the OU effect, or what exactly did he say? If Akula stated he thinks 
it is an NMR effect causing the OU in this type of setup, when Akula is referring to this NMR or NMR-like effect,
does he think this effect is occurring in the copper wire in the grenade coil itself, or in the ferrite in the yoke
core, or in the copper windings on the yoke core, or where exactly dies he think this effect is occurring?

Also, have you asked Akula if he thinks Ruslan's various supposed self running device video demos are real or fake?
It might be helpful to know what Akula thinks about Ruslan's videos.

akula always have approach from the NMR point of view. Also he frequently is referring to Lithuania Yoke experiment when explaining about tuning, etc.
In regards to Ruslan and akula relationship they are not on best opinion on each other and feels more competitors who do not like each other.
But both of them are referring for making standing wave and making electrons move on bucking coil of grenade.

There are many circuits reverse engineering attempts. What Ruslan and akula did with grenade coil connections seems are different if there are no hidden truth about Ruslan case. In the end what akula is saying privately is more comparable with Dally circuit and makes more sense when doing series resonance on inductor. The grenade coil is like Tesla coil just making more current than voltage due opposite winding on L3-L6 to L1-L2. So the top winding goes to the ground and the winding under inductor become "hot" end and this is where top load from the Tesla coil is on.
And the yoke becomes "mediator" in akula case which is same as in Dally circuit.

Thanks T, but your statements has me confused again.
Some months ago you told me the grenade (according to Ruslan) needs to be ALL layers in the same direction.
Thats what i have right now, but now you mention:

"The grenade coil is like Tesla coil just making more current than voltage due opposite winding on L3-L6 to L1-L2."

Does that mean that according to Akula the Grenade should be (like it was) layers 1, 2 CW, layers 3, 4 and 5, 6 CCW?


Thanks,  Itsu

Yes, this is indeed a good question for T1000 to ask Akula. Also, has Akula actually told T1000 that he has achieved overunity with his device. We see video demonstrations suggesting that this is the case but has he confirmed this to T1000? T1000 wrote earlier:-

 "After few hours with changing coils connections and frustration I made call to akula and asked how he was tuning his version of device. It turned out he is using 28-30T yoke winding to power Tesla coil and the grenade coil output is going directly to the load. Also he is trying to get standing wave with reflection from the ground under end of grenade and the resonant harmonic frequencies are in range with electrons movement Larmor frequencies. Which makes electrons push for the gain in the output."

This statement is saying that akula has not yet achieved a standing wave situation. It was my understanding that this was necessary to achieve a self-running situation which equals overunity, so has Akula really achieved this??

It was me with under unity on the current setup. akula had over unity for long enough time already with multiple devices. Just obviously it is highly experimental stuff so still not reached consumers like you.

Screenshot 2 shows a not so nice squarisch ringing signal.   
Not sure where that squarisch comes from as it should mostly get its input inductively from the inductor coil which as we see has a nice sine wave.
I measure on the input sides (AC side) of the FWBR.
The superimposed ringing (500/600KHz) probably is the grenades own self resonance or subharmonic as it is there with or without the nano-pulser active.
I still have the 28 turn secondary from the yoke connected in series with the grenade/FWBR.
No grounds are used other then the HV probe ground.
Itsu

Hi Itsu. If you are measuring the waveform on the AC side of the output FWBR, I would think that when the
diodes are conducting current though the light bulb load that this is squaring off the top of the sinewave coming
from the grenade coil. If you disconnect the light bulb, the waveform should look more like a sinewave
if this is the case.

I made some measurements on the inductor coil, see screenshot 1 and the grenade output, see screenshot 2


Screenshot 1 shows a nice sine wave from the series LC resonance across the coil with a slight hickup on tops and bottoms.
This is probably due to the push pull square wave driving it.
I put the nano-pulse exactly on top of this top hickup, and then there is some interaction going on, like
a slight flickering of the 40W bulb connected to the grenade (via a bridge rectifier) and the input current is also fluctuating.

By the way, all is being driven from one 24V battery stack (5/6A)

Screenshot 2 shows a not so nice squarisch ringing signal.   
Not sure where that squarisch comes from as it should mostly get its input inductively from the inductor coil which as we see has a nice sine wave.
I measure on the input sides (AC side) of the FWBR.
The superimposed ringing (500/600KHz) probably is the grenades own self resonance or subharmonic as it is there with or without the nano-pulser active.
I still have the 28 turn secondary from the yoke connected in series with the grenade/FWBR.

No grounds are used other then the HV probe ground.

Itsu

Hello Guys,

I will make a summarising document where all test resuts and attemps will be listed.
Even the coil setup, system configuration and sync method will be described.
We can all refer to this document so we keep on track. ( i see there is discussion about coil configuration,...we have information about sync approach,... and more what will be usefull to put in one document.

See it as a project approach document,..  i will post it tomorrow and hope we can use it as a tracking document.

Goodnight 

  Verpies:
  So, as you were worried about me...
  I've been cross-theading my brain lately. Trying to figure out the best easiest way to obtain the "effect".  As usual...
  So, I've been in Exciter/Kacher building mode, to see if I can put together a circuit on a bread board, that has some guts to it.
What I'm hung on now is,  not having the right recommended transistor, the 2SC5200.  I'm currently using the 2SC5251 transistor, but it's working very weakly. Much less gain from it, than my previous 1500v, 8A horizontal deflection Tv transistor, which ran my Kacher for several months.
   As my idea with the Kacher, is to ultimately feed it with HV, from the induction circuit, once rectified, like with something like 1000v volts, or so. If doable.
 
   So, for now that's what I'm up to, building up several Kacher/Exciter circuits that have some balls to them.  Excuse my French.
   I like those wide white streamers shown in the video of Geo's rig. So, I'm working on doing the same...
   
   I don't skip a beat of what's going on in the forum. Even if I don't post, don't think that I'm not on. 
I've just been keeping my hands busy building circuits.
   
   I've also been watching for Geo and Itsu's results. 
While I'm still focusing on the Ruslan type of replications. 
As the Akula/Ruslan devices looks to give the best bang for the buck, and as Ruslan has provided at least some of the needed info to replicate it.  Unlike,  some of the other secret self running devices out there.

   

  I was finally able to get a hold of some 2SC5200 transistors for the Kacher driver circuit.  Now, we'll see what happens once the right transistor is installed on a small breadboard, which I've already built up for the new Kacher circuit.
  To the bench...