Hi Jeg,

i see a lot of 2 stripes resistors (meaning 2W) in your 12V supply line feeding both the TL494 and the IR2110.
This points to some current flowing there, so you might be right by suspecting this could cause some 12V voltage fluctuation.

I would have both the TL494 and the IR2110 to be on separate regulators, and have a 10uF tantalum capacitor across
the IR2110 voltage supply lines to aid in the boost to charge the gates capacitance.

Also, i would add some heavy capcitors on the 12V regulators output like a 470uF electrolytic cap and a 0.1uF ceramic cap.

Finally the layout/length of the wires and components could be of importance, but that would be hard to debug.

Regards Itsu
 

Hi Jeg,

i see a lot of 2 stripes resistors (meaning 2W) in your 12V supply line feeding both the TL494 and the IR2110.
This points to some current flowing there, so you might be right by suspecting this could cause some 12V voltage fluctuation.

I would have both the TL494 and the IR2110 to be on separate regulators, and have a 10uF tantalum capacitor across
the IR2110 voltage supply lines to aid in the boost to charge the gates capacitance.

Also, i would add some heavy capcitors on the 12V regulators output like a 470uF electrolytic cap and a 0.1uF ceramic cap.

Finally the layout/length of the wires and components could be of importance, but that would be hard to debug.

Regards Itsu

Hi Itsu

Hmm. Ok. I will add some heavier caps to see the behavior. I use two regulators, one for each chip. In general, my outputs right now are acceptable for my needs. If I could also debug this power supply decoupling then I would be more than happy.

...
I highly recommend (unless you already have a self runner), replicating what Woopy demonstrates here:
https://www.youtube.com/watch?v=94yCfy8z4lc
...

That video of Woopy's is in turn a replica attempt of one of Delamorto's video. See here original video:
https://www.youtube.com/watch?v=3ZN1zFzgQkk

Ok thanks for your info

Hi Nick. I think there is a chance at least that if the Kapanadze OU effect is real, that once it is understood
it may turn out to be something pretty straight forward and simple. Akula is very good at designing circuits
of all types and he may have made his device more complicated than it really needs to be. Since Kapanadze
didn't want people to know what he was doing, he most probably added various things to deliberately try to throw people
off about how it is really working. Akula may have done some of that as well. The underlying principle could be quite simple,
so a simpler device that produces high output power is at least conceivable to me. As for Ruslan, well I think I am probably not
the only one who at this point doesn't really trust anything he is saying... 

I am going to continue on sticking to basics and try to find the OU effect by doing various experiments related to
the possible principles behind these devices. From very early on I think it was clear that what Daly and Akula
seemed to be doing was combine a high current waveform created via LC resonance with a timed HV waveform or spike of some type. So that
is where I will continue to experiment.

P.S. When the effect is found I think there should be little doubt. We are not talking about a difference of a few Watts
or so between input and output with these devices. If someone hits the effect, they should see a very large amount
of power available at the output, and there should be little doubt at that point that they are probably seeing OU.
If someone is just seeing a difference of maybe a few Watts, it is more likely they are just overlooking something or
they are making a measurement error.

void my name is name Deggory Devassy
i am no man in disguise here ,if you search peswiki site ,you can get little info about me.

I knw many have concern that kacher secondary coil cannot handle 4000 watts power output. Because  of the thin wire used it cannot handle high amps .But i believe the coil towards the right converts high voltage low amps to low voltage high amps.

If you see this youtube link ,his circuit is able to light 100 watts of light from tesla receiver coil connected to earth.
https://www.youtube.com/watch?v=ARCLD3qgjmI

Lets assume the circuit is OU or self loop ,but if tesla coil deliver 100 watts put from receiver ,may be with ruslan or akula coil we can amplify the output. 

Фонарик по схеме Акулы на 30W

https://www.youtube.com/watch?v=SSc74dSARLA

I's not fee energy, as soon as the power is removed the red light goes out, that's the 494 power gone then you can see the white LEDs start to die, he then cuts the video before you see any more

AG.