https://www.youtube.com/watch?v=HZ5ZY3L1O9s

This material does not prove anything but there is a visible flare if this is true?

Agreed. The current increases as the bulb gets brighter, which is to be expected.

Hi Itsu. Thanks for the help. I will measure my primaries asap and I'll report. My inductor is 12.5m which is the 1/3 of my 37.5m grenade.
About hissing, do you think that it matters if my28T is on the air? I mean it is not connected yet. I have wind it but it is still disconnected. Only the 3T is on place and measures are taken like that.

Jeg,   i don't think so, my setup ran for severall weeks with the 28 turn secondary open, no hissing sound heard.

Itsu

Agreed. The current increases as the bulb gets brighter, which is to be expected.

but significantly capacitor charging in fast mode and what could that affect the current efficiency rate out- whence comes the rest of the energy from the fourth dimension buu haaa.

Hi.
Itsu
Thanks for the changes but I thought that at the outbreak of HV. across the wima caps (in resonance) draw the energies Ruslan says that shifts the phase current?
 you tuned the kacher to run (pulsed) on a third of that 2.65Mhz = 883Khz with you I do not see a flash- 0.5V voltage increase with or without the kacher ontop
Now let me ask you a question, have you tried using the small transformer to measure the current with a resistor ,so that the peak voltage of it was ripped from the driver pulse Kacher?
 -because you did not show where you got 15 kHz input to the controller Kacher or you connected in parallel a gateway one channel Pusch-pull am I right?
or even simply where the mustache at the top of the sine
I wonder if this is possible:

https://www.youtube.com/watch?v=HZ5ZY3L1O9s

This material does not prove anything but there is a visible flare if this is true?
info:
It uses a 200 watt light bulb under the push-pull 25 volts 2.5 amps -At the inclusion HV ampere consumption of the battery
increases to 3 Amper.
The pulse is powered by a 50 Volt draws 1 Ampere.

as instability pulses fall in a different place
https://www.youtube.com/watch?v=QmsZEGyJfBQ
Hmm.

TT29,

i have the moustache like signal (peak) always on top (or bottom) of the voltage sine wave of the Wima caps, see here:

http://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg463623/#msg463623



The kacher drive pulse (which is a different pulse) i got from the PLL output via the S1 switch, see the diagram:
http://imgbin.org/images/26553.jpg.

Presently it comes from a switch, but fed by the little TL494 circuit output (which is also the input for the MOSFET drivers driving the MOSFET's/yoke),
so i can select if it pulses on top of on bottom  (180° shift) of the Voltage sine wave of the Wima caps.
With a potmeter (R5) a can shift this pulse anywhere (~180°) on this sine wave and with R9 pot a can narrow the width down.

Hope that answers your question(s).

 
Itsu

T-1000,

i think my current transformers are where you mention they should be (like on the diagram), but i cannot get them to peak on the current, instead they peak on the voltage.

See above screenshot.

Regards Itsu

current trough a wire or resistance will produce voltage. if you want current what you g9oing to do with it ? feed voltage into VFO amplify it perhaps invert it but you will need to rectify it like a discriminator does to get right phase.


AG

I do not know if that makes any sense but if so it could be work

This is it Itsu.

PWM percentage even at 45% (maximum) does not increase the voltage across inductor's capacitor over than 310V.!!!

It almost looks like your primaries are in bucking mode and the signals counter act on each other.

They are in bucking mode cw-ccw since yesterday. Do you think that this is the problem?. I use a 220 to 24v dc converter at 16.5A

It is not logical both mosfets to fire together.