Just left a comment on your channel. Are you sure the lights being switched is not just causing interference in your scope? Interesting that you are getting ac from your cells though. Thanks

You stimulated me into making a little video. I didn't have time to set up any cells....

http://www.youtube.com/watch?v=oSfSswzlWJw

 


I'm pretty sure that your cells will be producing an actual straight DC level, and that you will see some noise on top of that ripple. May I suggest the following:

1. Use an attenuated probe, 10x. Hook the "ground" or reference lead to the cathode of your LED. Hook the "tip" or probe to the anode of the LED.
2. Set the channel input to DC coupled, 10x to match the probe, and 1 or 2 volts per vertical division. If your scope has an offset setting, set it to Zero, or manually set the channel baseline to the center graticule marker.
3. Set the trigger to trigger on the same channel you are reading, and at a level of about 0.5 volts positive.
4. Now scan through the various horizontal timebase settings to see if there is some slow or fast oscillation or pulsation you might be able to catch.

This should show you the DC level that your cells are putting out. Once you know the value of this level by looking at it at reasonable resolution and DC coupled, then you can see if there is a ripple sitting on top of that DC level.

1. Switch the scope to AC coupled. You should see the trace from "4" above drop down to the baseline graticule marker in the center.
2. Now change the vertical resolution from the 1 or 2 volts you had before, down in stages down to 200 or 20 mV per division. You may have to reset the trigger or set it to "auto". (DO NOT push the "auto everything" or auto setup button, you'll lose your settings! Just set the trigger itself to "auto".)

Now you should be seeing noise or ripple similar to what you had in the video, only a more stable display. You can read the magnitude of the noise/ripple, remembering that the center graticule marker now indicates the DC level that you read in step 3 above, not "zero", so your noise or ripple isn't really AC, it's a fluctuating level of DC.

ETA: In case it isn't clear by now... in general you should keep your scope channels set to "DC coupled" if you want valid voltage readings. Some specialized measurements require the use of AC coupling, most do not. It has really nothing to do with whether you are measuring an AC or a DC signal. The "AC coupled" feature just switches a capacitor in series with the probe input instead of the straight wire "DC coupled" setting. So the capacitor blocks the DC component and passes the fluctuating level of the signal. That's all it does.

Noticed the keshe foundation website was selling something new. A kit that is able to produce solid CO2 (in 'plasma matter' form) using a specially treated plate and a zinc/nickel? plate.

http://keshefoundation.org/shop/category/view/5.html

I must say the selling price is negligible compared to the claim, I presume to be producing an unlimited amount of this gooy CO2 material (and even energy?). I don't know if the kit comes with any instructions or more information but as it stands there is very little information on production rate, the degradation of the "nano" plate and how exactly the power is produced.

EDIT:

Found the more extensive 2 part video on this kit:
https://www.youtube.com/watch?v=D12PKWEo7iY&index=1&list=UUP1CJKRkg6ImllD6N2qIKHg

And also a quote from someone of the keshe foundation:

Neo,
 
 Please listen to the 31st workshop (available for download in the banner above for Knowledge Seeker Workshops).  The plates will last a long long time, and create GANS from the start.  The Keshe Foundation is in the process of teaching what we can do with the GANS created, so keeping it safe in bottles will be the best idea.  The salt water can be any salinity, however, I believe the best option is to see what works for you, there is no wrong answer.
 
 The harvesting of the GANS can be done at any point, just use your best judgement on when you want to harvest.  With the prototype plates, I believe that they where harvesting every 24 hours or less.
 
 With the changing of the water, it is not needed.  Just add water as it evaporates.  Again, this isnt an exact science, because creation has never needed measuring cups. 
 
 Good luck with your GANS creation and thank you for helping clean up our planet!!
 
 WebKFteam

back to 2012
http://www.overunity.com/12661/mehran-t-keshe-technologies/msg334330/#msg334330

Noted, but this is the first time the tech is available for public hands and scrutiny. This is either revolutionary or suicide as peers that are able to review this are pretty much the whole world.

Perhaps some type of  catalytic conversion of atmospheric carbon dioxide to formic acid via  nascent h2? H2+ CO2 = HCOOH.very useful fuel is formic acid.

HHO generators have no known harmful effects on healthy engines. HHO generator manufacturers often assert that oxyhydrogen helps clean carbon deposits from the engine's valves, but that's unlikely since HHO gas has no solvent effect whatsoever.

 Large amounts of quick-burning HHO in the cylinder itself may help to burn off some oil residue from the piston and cylinder head, but this premise hasn't been tested thoroughly enough to confirm.

Our Website: http://www.ckkar.com/

So, what is the general consensus on on this guys plasma work. I personally have never heard him come anywhere close to tangible technical description of his work.

....

Very frustrating that there are people like this who do not realize that if it is really based on your home brew physics and works then whats the problem with open sourcing all the pertinent build info plus validated proof of the functional concepts.

- David

He is a scam artists who serves as an inspiration to other scams like the QEG people. He is also very deluded.
Kind regards
Mark