http://www.youtube.com/watch?v=KFGiEQecEsQ

Skycollection ( http://www.youtube.com/user/skycollection ) has published the new video above.

Again he does not do any conclusive input and output measurements. Very strange, because that would be a straight forward thing to do.

Greetings, Conrad

Well something is weird. The big battery to the right seems to be connected to the cap and the meter is measuring the battery? The battery starts off at 11.1v. That is completely discharged, as  far as  useful charge as it was intended.

That is the reason it can be taken to 29v.  And then it even stays near 20v after the gen motor is stopped. That tells me the battery is in terrible shape and the cap is "trying to hold' the charge but it is leaked into the battery, and the battery doesnt seem to want much of it as slowly as the voltage is dropping, or the cap/battery voltage would have dropped down to at least something over 11.1v pretty quickly.

Its a shame that some show so much but it all remains a mystery.

Mags

Well something is weird. The big battery to the right seems to be connected to the cap and the meter is measuring the battery? The battery starts off at 11.1v. That is completely discharged, as  far as  useful charge as it was intended.

That is the reason it can be taken to 29v.  And then it even stays near 20v after the gen motor is stopped. That tells me the battery is in terrible shape and the cap is "trying to hold' the charge but it is leaked into the battery, and the battery doesnt seem to want much of it as slowly as the voltage is dropping, or the cap/battery voltage would have dropped down to at least something over 11.1v pretty quickly.

Its a shame that some show so much but it all remains a mystery.

Mags

Yeah I agree Mags, the battery is badly sulfated or damaged and if he does not mention that in the video he is either very uninformed of being deceptive.
I also seen nothing in the video to indicate and miraculous charge rate.

http://www.youtube.com/watch?v=KFGiEQecEsQ

Looks to me like he is a neat experimenter, but doesn't understand what he is doing/seeing or he is deceptive/misleading.

Basically I would not watch any more video's without being very very skeptical.

If he wants people to not question him he should not make video's.

The result we see in the video is perfectly normal behavior for a badly sulfated battery fed energy from a coil discharge. That is the effect the video shows.

The cap is probably there because without it being there the voltage generated at his drain or collector pins would destroy them
due to the battery not being able to take on the energy quick enough. As many of us know quite well. We've seen the same effect.
That is why neons are used between the collector and emitter  pins on desufator circuits, because if the battery is too badly sulfated
the developed voltage will usually damage the transistors. Adding a large capacitor across the charge battery is common practice for
when a battery is so sulfated the safety neons fire continuously.

Haven't we moved past pulse motors and sulfated battery effects ?

I'm not attacking him either just making observations.

Cheers

P.S. Isn't this getting way off topic. It has as much to do with "Delayed Lenz Effect". It's a pulse motor trying to charge a badly sulfated battery.

What exactly was he claiming for the video ? I don't see any "new" inductors.

...

sorry for the delay in answering
no video cam available and I do not like to post videos neither,  for a main reason: I am very short in measurement knowledge, therefore, I am unsure of the results gotten from many of the experiments done . .  so the least thing I want is to mislead or give false info, as I have poor measurement equipment even no oscope.
I am here mainly to learn, and something I found very often, is people showing videos with no specs nor schematics and many of them showing only voltages but no Amps, which is very frustrating.
IMO measurement of output pulsed DC without a scope originates many wrong conclusions, as well as batteries behavior.
Anyway, taking constructive criticism as an attack is just a childish behavior. . . . so your considerations about the attached pic are very welcomed.
Is just to clarify what I meant for a "sliding coil" in my previous post.
If any is interested I may post as many specs or schematics as required. Of course I insist in the poor measurement subject.
The motor type Adams is driven by 2 hand made electromagnets, a reed switch and a 2N3055 transistor.
I just placed a voltage divider before the reed input as to elongate its life, using just a small current/voltage at the transitor base.(I know this way is not efficient because of resistance looses)
It works from 3V to12V. (but at 12V the trans. gets warm, so I use 6V as average input, the mA input varies also)
Average rpm at 6V- 500mA: 3600 rpm.
About the sliding coils, I tested many, mainly tesla series bifilar ones (solenoid) and mainly with 3500 turns, the higher output voltage was fitting the output coil physicaly closer to the driving coil, but average Amps were always quite low. Very easy to load many leds but very weak with resistive loads.
The lack of a Scope, do not allows for an accurate search for the resonant condition. I go as far as I can.
Cheers
edit-forgot to say: no input or rpm changes perceptible at any loading condition.

@ALVARO-CS,
 
             That's called a "Piggy Back" coil. It shares the core with the power coil. Gadgetmall reprted O.U. results with one just like it. Thank you for showing us pictures of the build. Very interesting test bed! You mentioned earlier that the output coil could be adjusted to help deliver a kick to the rotor? A lasertach would sure be nice to help confirm any "Lenz Delay" effect. 

sorry sinchro, I may be explained it in a wrong way. What I meant is that the output increases as the output coil gets closer to the driver, but not difference in rpm nor in input power.(no kick)
I even noticed no changes starting the motor and adding the output  coil (already loaded) after max rotor speed.
The driving circuit acts as if the output coil was invisible.

"Lenz Masking"! I implied a motor might be concievable, but your accomplishment stands as an advance unique unto itself. I'm certain Gadgetmall confirmed your results with his setup. Very impressive outcome. "Zero Lenz" output coils are not the Unicorn!
 
Quote from above:

"this ones are series bifilar"

What coils are serial bifilar, the power, output or both?
 
The power coil pulse may be all the output coil gets, but so what, it's free energy. The output coil needs to be tested alone on the sliding core for "Lenz propulsion" effect".

wait wait, I have to emphasize in avoiding any claim, as I said, the lack of accurate equipment may drive to inapropriate measurements. (no hurras by now please)
This is the first time I post this here (or anywhere), and not aware of related Gadgetmall accomplishments. (I miss him in the Joules thief thread)
If someone here would be interested in replicating such a setup, and make some oscope shots, THAT would be the way to confirm or deny it.
If this will be the case, I would have a pleasure in posting the physical specs  as No of turns, sizes etc.(I don`t know the flux density of my magnets from HD, neither the saturation degree of the ferrite core, from a AM radio)

cheers

Moire patterns:

https://www.youtube.com/watch?v=Cn-TNQXl9KE

Lorentz force acting on moving charges resulting in moire patterns:

http://www.youtube.com/watch?v=h89TaH6Er1Y

Alvaro:

That circuit that you are using may damage your transistor.  If you notice when the transistor switches off the inductive energy gets discharged inside the transistor.

MileHigh