Cookies-law

Cookies help us to bring you our services at overunity.com . If you use this website and our services you declare yourself okay with using cookies .More Infos here:
http://www.overunity.com/5553/privacy-policy/
If you do not agree with storing cookies, please leave this website now. Many thanks for your understanding.
Amazon Warehouse Deals ! Now even more Deep Discounts ! Check out these great prices on slightly used or just opened once only items.I always buy my gadgets via these great Warehouse deals ! Highly recommended ! Many thanks for supporting OverUnity.com this way.

User Menu

FireMatch

FireMatch

CCKnife

CCKnife

Poplamp

poplamp

CCTool

CCTool

LEDTVforSale

Magpi Magazine

Magpi Magazine Free Rasberry Pi Magazine

Battery Recondition

Battery Recondition

OverUnity Book

overunity principles book

Arduino

Ultracaps

YT Subscribe

Gravity Machines

Tesla-Ebook

Magnet Secrets

Lindemann Video

Navigation

Products

Statistics


  • *Total Posts: 488469
  • *Total Topics: 14373
  • *Online Today: 44
  • *Most Online: 103
(December 19, 2006, 11:27:19 PM)
  • *Users: 2
  • *Guests: 214
  • *Total: 216

Facebook

Author Topic: Simoscopy  (Read 23804 times)

Offline webby1

  • Hero Member
  • *****
  • Posts: 2948
Re: Simoscopy
« Reply #120 on: June 05, 2016, 07:29:02 PM »
Here I have increased the CV to 75 degrees per second and made 2 full cycles,, just a little over.

Now the CV is a cost of apr 75J per cycle but the damper to constant torque is up to 130%

Free Energy | searching for free energy and discussing free energy

Re: Simoscopy
« Reply #120 on: June 05, 2016, 07:29:02 PM »

Offline webby1

  • Hero Member
  • *****
  • Posts: 2948
Re: Simoscopy
« Reply #121 on: June 06, 2016, 02:00:20 AM »
Here is a screen-shot of my summary spreadsheet,, it is only the totals from a bunch of consecutive runs that were really slow.

I will also post the last run,, it overlaps with the first run about 1\2 way through the run.


Free Energy | searching for free energy and discussing free energy


Offline webby1

  • Hero Member
  • *****
  • Posts: 2948
Re: Simoscopy
« Reply #122 on: June 06, 2016, 02:01:18 AM »
Here is that last run,,

Offline webby1

  • Hero Member
  • *****
  • Posts: 2948
Re: Simoscopy
« Reply #123 on: June 07, 2016, 02:40:10 PM »
I took the system and turned off parts of what I am using,, just to see what happens.

With the system not active things get a little interesting,, in one setup there was an oscillation that skyrocketed,, with an input torque and nothing to slow it down that is what you would expect.

I went and changed things around, still without the full system active,, until I could get into a stable run and when stable the sim showed a net zero by way of having some runs being over by a little and some being under by a little.

Then I took that setup and engaged the whole system.

This is with all of the math done and shows what the average values are for a full cycle,, or very close to it.

The .xls file is too big,, so this is the .ods file


Offline webby1

  • Hero Member
  • *****
  • Posts: 2948
Re: Simoscopy
« Reply #124 on: June 09, 2016, 12:05:13 AM »
I am trying to get things to run smoother,, get the timing of stuff closer,,

This is with a few of those tweaks,, and I am not trying to optimize the thing just trying to get the sim to run smooth and consistent.

The gain is up,, interesting,,

I tried to only use the CV motor for 1\2 cycle but that ended up costing a bunch,, it was a loss,, I might try a few more times with that but I think that is a fail attempt after seeing the numbers so far.

This is the raw data dump.

Free Energy | searching for free energy and discussing free energy

Re: Simoscopy
« Reply #124 on: June 09, 2016, 12:05:13 AM »
Sponsored links:




Offline webby1

  • Hero Member
  • *****
  • Posts: 2948
Re: Simoscopy
« Reply #125 on: June 10, 2016, 02:24:30 AM »
Here is the tweaks in place and the damper set at 30,, and at 31,,

Somewhere between these two settings the damper would be able to run the constant torque motor.
These are the raw data.

This leaves the input to the constant velocity motor which shows a negative input energy over one cycle.

What is also interesting is that the more I take out from the damper the less gain is present,, to the point of having no gain.

Offline webby1

  • Hero Member
  • *****
  • Posts: 2948
Re: Simoscopy
« Reply #126 on: June 10, 2016, 02:25:00 AM »
Second data file

Free Energy | searching for free energy and discussing free energy

Re: Simoscopy
« Reply #126 on: June 10, 2016, 02:25:00 AM »
Sponsored links:




Offline webby1

  • Hero Member
  • *****
  • Posts: 2948
Re: Simoscopy
« Reply #127 on: June 11, 2016, 01:47:40 AM »
Here I have tweaked the sim to show a loss.

It will run stable showing a loss or a gain,, even tho there is no loss or gain, it is all a net zero condition for the parts by there own interactions but when the whole system is set in motion correctly they share interactive movements with force that create a work gain or loss for the operator.

Offline webby1

  • Hero Member
  • *****
  • Posts: 2948
Re: Simoscopy
« Reply #128 on: June 19, 2016, 08:44:59 AM »
Have you ever wondered what would happen if you could capture something from an impulse??

Here is a fun one that captures part of that.

The sim errors due to this interaction,, it is fun in that this time instead of it costing me this input energy it is returning my input energy,,

That is 3520J in and 250,000J out

 

Share this topic to your favourite Social and Bookmark site

Please SHARE this topic at: