Free Energy | searching for free energy and discussing free energy
Solid States Devices => Kapanadze devices and replications => Topic started by: hartiberlin on June 27, 2014, 11:59:39 PM
-
2 German Visitors were at Akula´s (Romans´s) place and tested again in the garden the Akula Free Energy 1 KWatt generator that only needs a ground cable to operate. No Fuel just a ground cable to capture free electrons from the ground.
Unfortuantely this video was filmed by 90 degrees rotated so the frame size when corrected is so small.. Just watch it please in Fullscreen.
I added an English translation Caption to the video, so you have to press CC Caption button at the right lower border of the video to see the English language subtitles translations..
On the Android Youtube APP you need to press the 3 dots at the upper right side of the video screen and then press the CC icon to see the subtitles..
Well Roman ( Akula ) will be in Germany in July and I hope to meet him then.
Looking forward to report more about this great device.
Many thanks to Roman and the German visitors for making this video publically available via my channel.
http://youtu.be/QlLTpDFLWrs
Regards, Stefan.
-
Thanks for posting, and also for the captions! It seems to start out with saying "2013" though... so this video visit isn't new, but from last year some time?
But... that black ground cable again. I left this comment on the video:
(start comment)
It looks like the same old ground wire that has been discussed before. We really really need to see both ends of that wire disconnected, shown to the camera, and then reconnected to the pipe and the apparatus, live on camera. You know I would do this!
Closeups of other demonstrations have shown that the black wire appears to disappear into the inside of the ground pipe, and the connection to the apparatus itself is never shown in detail. The "ground wire" could easily be a coaxial cable connecting to a buried power line coming up to the pipe. Of course touching the pipe does nothing! It is genuinely grounded. But the centre conductor is of course supplying the power.
(end comment)
Also... you cannot walk around that close to an actual Tesla coil without affecting its resonant frequency and power.
-
2nd demonstration of the Akula 1 KWatts Selfrunning Free Energy Generator system.
I added an English translation Caption to the video,and a few highres pics of the device at the end.
http://youtu.be/JhnrwwpXEPw
Regards, Stefan.
-
The "ground wire" could easily be a coaxial cable connecting to a buried power line coming up to the pipe. Of course touching the pipe does nothing! It is genuinely grounded. But the centre conductor is of course supplying the power.
Well, this is really only a ground cable as you can see from all the other videos which were already posted about this device. Not a coax cable, just a pure big copper cable.
Well these German guys are marketing guys, who have visited Roman. so they unfortunately missed
to test it some more or if they have tested to disconnect, I don´t know, if they have filmed it.
When Roman will be in Germany soon and I will have a chance to see the device we will of course test it all
in all details and also film is all..
Regards, Stefan.
-
I've watched a lot of those videos and I'm not convinced at all. In the present video when the man picks up the cable you can see that it's pretty light and pretty flexible, not like a "heavy copper" cable at all.
But I trust that you will do a good job when you visit. If you are allowed to, that is. You and I know that often, in these cases, the device breaks down just before the visitor arrives with the test equipment, and can't be fixed until after the visitor is due to leave. So I would suggest that you strive to arrive a day or two earlier than he expects.
Find a two-meter length of copper pipe, take it with you to his house, and demand that he drive it into the ground in a location you select, then hook up his ground wire to that. He won't do it. Why not? Be sure to suggest it, at least, and tell us what he says.
;)
-
Hi All,
Well, your opinion is correct TinselKoala.
Regards
-
Speaking of copper reminds me of what Mr Clean said about grounding, that an
iron pipe grounding has better effects as an copper pipe.
You can get a 'Kreuzerder' at the 'Baumarkt' with all parts to attach the
earthing cable.
Akula is a public person , active in various forums, a radio station and so.
He would give up to much, if all of his devices were a fraud.
Actually only one wire is needed to transmit power: HV AC and the end of the wire
a avramenko plug: voila. But you could not touch this!
And one video of the Barbosa -Device Replication is a electricity stealing circuit.
No one could fool me.
->At the end : he should be allowed to use an iron pipe for grounding purpose also.
If would be nice , if he could desribe the building details of a simpler device ,
such as the ring transformer , driving the led.
-
My opinion is just an opinion, but it's based on my knowledge of Tesla systems, psychology, and stage magic illusions, along with my careful observations of what's happening in the Akula videos. It would be easy to prove my opinion wrong, with a site visit from someone we trust who might be allowed to perform some very simple tests. Or even an "interactive" kind of live test session, where Akula would respond to some questions or suggestions from one or two observers on the internet.
As to whether iron or copper makes the "better" ground rod... where is the data? To make this kind of claim, wouldn't you have to show that a device behaves differently -- somehow "better" ? -- when connected to the iron rod, than it does to the copper rod, _all other things_ being equal? Rods in the same dirt, same moisture content, cabling equal, device under test properly monitored, etc. The results could be shown in a simple graph or two, showing the difference in the device's behaviour or performance when connected to each rod material. I would love to see this data. Where is it, please?
-
It's in on of Mr Cleans (kdkinen) yt videos , if I remember correctly. If I find I will post here.
-
As bad as I hate to admit it ::) I have to agree with TK
Older homes here in the US used grounding clamps to secure the mains ground to water pipes, He should use a stand alone grounding rod.
If you build a device thats tied to ground in any way the electric company's are going to accuse you of stealing electricity, and the device will be outlawed.
-
I've watched a lot of those videos and I'm not convinced at all. In the present video when the man picks up the cable you can see that it's pretty light and pretty flexible, not like a "heavy copper" cable at all.
But I trust that you will do a good job when you visit. If you are allowed to, that is. You and I know that often, in these cases, the device breaks down just before the visitor arrives with the test equipment, and can't be fixed until after the visitor is due to leave. So I would suggest that you strive to arrive a day or two earlier than he expects.
Find a two-meter length of copper pipe, take it with you to his house, and demand that he drive it into the ground in a location you select, then hook up his ground wire to that. He won't do it. Why not? Be sure to suggest it, at least, and tell us what he says.
;)
"A time-varying magnetic field external to the Earth induces telluric currents (http://en.wikipedia.org/wiki/Telluric_current)—electric currents in the conducting ground. These currents create a secondary (internal) magnetic field. As a consequence of Faraday's law of induction (http://en.wikipedia.org/wiki/Faraday%27s_law_of_induction), an electric field at the surface of the Earth is induced associated with time variations of the magnetic field. The surface electric field causes electrical currents, known as geomagnetically induced currents (GIC), to flow in any conducting structure, for example, a power or pipeline grid grounded in the Earth".
Piplines can deliver ten amps of D.C. Telluric current through a water pipeline matrix, depending on the location. It would be ruinous for Akula to attach his ground to a copper pipe that TK positioned arbitrarily somewhere!
-
Well, Synchro.... you have finally explained why Akula's devices won't work anywhere but at his house! He has tapped into specific telluric currents and without weeks of careful probing with iron pipes to find a new telluric current, he won't be able to make it work at some arbitrary spot. Genius! That will allow him to prolong his fame quite a bit longer.
Does the fact that he seems to operate, or is closely associated with a _radio broadcast station_ have anything to do with the fact that his _tuned circuits_ are producing "free energy" I wonder?
-
More then just an iron pipe. It's the entire pipeline grid.
-
There's a guy lighting 120 bulbs connected between his water pipe and the neutral ground line in the wall socket. He's doing basically the same thing.
Here's a quick and dirty test to find out if you're over a Telluric hot spot. Take your digital multi meter into the kitchen; Place one electrode in the ground hole of the wall socket, hold the other electrode to the water faucet, and read the voltage! Lol!!!
-
Polite Request: Let's keep this thread "On Topic Only!"
Hi Fellows,
Can we PLEASE keep this thread precisely On Topic ("Akula's German visit"). Thanks in advance!
Owing to the extreme significance of this "near term" event, and it's potential huge Global impact,
your consideration in this matter is greatly appreciated...
Your valuable input, including any specific degree of skepticism, is welcomed; however there are any number
of other threads that will gladly accommodate your opinions and comments. Whether Akula's inventions work
or not will be soon flushed out by the meeting participants.
Hopefully just the actual meeting events and related outcome, if any, might be quickly and conveniently reviewed
here.
Again fellows; TIA
SAEC
-
Polite Request: Let's keep this thread "On Topic Only!"
Hi Fellows,
Can we PLEASE keep this thread precisely On Topic ("Akula's German visit"). Thanks in advance!
Owing to the extreme significance of this "near term" event, and it's potential huge Global impact,
your consideration in this matter is greatly appreciated...
Your valuable input, including any specific degree of skepticism, is welcomed; however there are any number
of other threads that will gladly accommodate your opinions and comments. Whether Akula's inventions work
or not will be soon flushed out by the meeting participants.
Hopefully just the actual meeting events and related outcome, if any, might be quickly and conveniently reviewed
here.
Again fellows; TIA
SAEC
So whom is off-topic here? What was it that was posted that you consider off-topic?
Bill
-
Apparently, trying to figure out how to tell a hoax from the real thing is always off topic. Along with making suggestions to the claimant as to how he can "prove" his claims in a more believable way.
-
from http://realstrannik.ru/forum/39-kapanadze/134930-ustanovka-ruslana-kulabuxova.html?start=288#225656
from http://realstrannik.ru/forum/48-temy-freeenergylt-antanasa/134896-akuly0083-15-kw-ustanovka.html?start=18#225512
-
The above Akula schematic is probably the one that I was hoping to find, thanks for posting it.
This second device from Akula's videos is the only one that we've had some sort of confirmation of authenticity, as proving itself to be a real self runner. So, I'm also hoping that the posted schematic is also actually the real thing, and not "almost correct", as like in almost pregnant.
However, this schematic does keep me scratching my head though, as not all components are fully marked, and some coil winding counts don't match what is seen in the video. None of the coil wire guage are shown. And, for example, the yoke's secondary coil, is not a multi tap 30, 45, 60b (I hope B refers to turns) as is drawn in the diagram. As it has about 20 to 30 turns, only.
What is the value of the capacitor that is colored green?
Yes, maybe I need to learn some Russian...
Anyway, if anyone knows...what are the exact turn counts on the long PCV tube, (the main oscillator's air coils), and, on the Kacher, also.
-
The above Akula schematic is probably the one that I was hoping to find, thanks for posting it.
This second device from Akula's videos is the only one that we've had some sort of confirmation of authenticity, as proving itself to be a real self runner. So, I'm also hoping that the posted schematic is also actually the real thing, and not "almost correct", as like in almost pregnant.
However, this schematic does keep me scratching my head though, as not all components are fully marked, and some coil winding counts don't match what is seen in the video. None of the coil wire guage are shown. And, for example, the yoke's secondary coil, is not a multi tap 30, 45, 60b (I hope B refers to turns) as is drawn in the diagram. As it has about 20 to 30 turns, only.
What is the value of the capacitor that is colored green?
Yes, maybe I need to learn some Russian...
Anyway, if anyone knows...what are the exact turn counts on the long PCV tube, (the main oscillator's air coils), and, on the Kacher, also.
30, 45, 60В is volts.
Green capasitor need chosse to resonance (17-27-37 kiloherc), baisycly i beleave any frenquency betwen 17-50 kiloherc, need chose that capasitor, I suggest, that be small power consumtion disconecting all secondaries windings. :)
-
This schematic doesn't make sense, how are they running a PSU on high frequency AC? did they change the diodes in it?
The driver circuit looks a bit complex unless you are looking for a timing/phase shift. the HV section looks to be problematic IMO, why not use a current transformer instead of the zeners? you can then trigger the self resonance without running the risk of burning your transistor. and keep some isolation in the design. some of the driver section could be replaced with a FET driver chip IMO, fewer parts required.
I think the same can be built using a 12v SLC Battery, an Inverter, a SSTC driver and some hand made coils. I have most if not all of those parts, I think I will play a bit.
-
This schematic doesn't make sense, how are they running a PSU on high frequency AC? did they change the diodes in it?
---
How Dally run PSU on hight frenquency? PSU have inside 4 diodes. You think, that that diodes can not rectifer 10-40 kiloherc?
-
@MenofFather,
Most switch mode PSU's use the least cost parts thus they would not usually use diodes that would support high Frequency sources.
As for why, check this out http://electronics.stackexchange.com/questions/97780/using-normal-diodes-to-rectify-high-frequency-waveforms
this provides a pretty good reason why cheap diodes fail in high freq applications.
I am saying that if the PSU used was not modified, I do not think the input bridge rectifier diodes are of the high freq type. I would like to see a schematic of that PSU and check the diodes to see. I even call on the above schematic as the bridge rectifier , "Br1" if not a schottky type will not function for long as this transformer is putting out 35khz correct?
Anyways, the design is similar to the one using a 50/60hz modulating signal if you look at it. The yoke is used to make a transformer that can support high frequencies, using the split core technique you might gain some efficiencies.
To me the 1Kw unit above looks to be using a tank configuration off the yoke to the cap and coil on the air core transformer. You said it would operate in the 35khz range correct? So this akula device uses 35khz with HV pulsing, has anyone checked the inductance of the coils or swept them? what is the operating freq for the tesla coil side?
so it looks like from the waveform the 35khz signal is 90° roughly out of phase with the HV pulsing.
Just sayin'
-
@MenofFather,
Most switch mode PSU's use the least cost parts thus they would not usually use diodes that would support high Frequency sources.
As for why, check this out http://electronics.stackexchange.com/questions/97780/using-normal-diodes-to-rectify-high-frequency-waveforms
this provides a pretty good reason why cheap diodes fail in high freq applications.
I am saying that if the PSU used was not modified, I do not think the input bridge rectifier diodes are of the high freq type. I would like to see a schematic of that PSU and check the diodes to see. I even call on the above schematic as the bridge rectifier , "Br1" if not a schottky type will not function for long as this transformer is putting out 35khz correct?
Anyways, the design is similar to the one using a 50/60hz modulating signal if you look at it. The yoke is used to make a transformer that can support high frequencies, using the split core technique you might gain some efficiencies.
To me the 1Kw unit above looks to be using a tank configuration off the yoke to the cap and coil on the air core transformer. You said it would operate in the 35khz range correct? So this akula device uses 35khz with HV pulsing, has anyone checked the inductance of the coils or swept them? what is the operating freq for the tesla coil side?
so it looks like from the waveform the 35khz signal is 90° roughly out of phase with the HV pulsing.
Just sayin'
Hi
I do agree the diodes typically used are 1n4001 1Amp or similar 3amp version.
Base on my research all full bridge rectifier that i have been searching for are designed to run on mere 50hz or 60hz only.
Not even spotted a 400hz version at all.
Unless its been modified with 400 or 600v fast response diode with around 100ns or less
-
@MenofFather,
Most switch mode PSU's use the least cost parts thus they would not usually use diodes that would support high Frequency sources.
As for why, check this out http://electronics.stackexchange.com/questions/97780/using-normal-diodes-to-rectify-high-frequency-waveforms (http://electronics.stackexchange.com/questions/97780/using-normal-diodes-to-rectify-high-frequency-waveforms)
this provides a pretty good reason why cheap diodes fail in high freq applications.
I am saying that if the PSU used was not modified, I do not think the input bridge rectifier diodes are of the high freq type. I would like to see a schematic of that PSU and check the diodes to see. I even call on the above schematic as the bridge rectifier , "Br1" if not a schottky type will not function for long as this transformer is putting out 35khz correct?
Anyways, the design is similar to the one using a 50/60hz modulating signal if you look at it. The yoke is used to make a transformer that can support high frequencies, using the split core technique you might gain some efficiencies.
To me the 1Kw unit above looks to be using a tank configuration off the yoke to the cap and coil on the air core transformer. You said it would operate in the 35khz range correct? So this akula device uses 35khz with HV pulsing, has anyone checked the inductance of the coils or swept them? what is the operating freq for the tesla coil side?
so it looks like from the waveform the 35khz signal is 90° roughly out of phase with the HV pulsing.
Just sayin'
Dally write, that he divice work and without diodes aditional, but with aditional diodes it work more stable So standar diodes, I think can rectify prety inought well frenquency up to 40 kiloherc, maybe with small eficienty. And maybe Akula remade little PSU (use faster diodes and less indution chokes).
It can operate in 35 kiloherc, yes.
That frenquency of Tesla coil, I don't know, but I gues, that betwen 500-2000 kiloherc. HV not pulsating, HV have standar sine wave. So is two sine waves. One let say 35 kiloherc, other, let, say, 1500 kiloherc. So I not imagniate how here can be synchronisation and how it can made any influence. See my video, were I showing in last video osciliogram with green sine wave? I here put oscilioscope on resoanant capasitor, who in akula schematic is green. And how you see I get same osciliograme like in ruslan video. Only my kacher frenquency seems lower and lower of it voltage.
:)
-
If a diode is conducting in a forward condition and immediately switched to a reverse condition, the diode will conduct in a reverse condition for a shot time as the forward voltage bleeds off. The current through the diode will be fairly large in a reverse direction during this small recovery time.
-
Dally write, that he divice work and without diodes aditional, but with aditional diodes it work more stable So standar diodes, I think can rectify prety inought well frenquency up to 40 kiloherc, maybe with small eficienty. And maybe Akula remade little PSU (use faster diodes and less indution chokes).
It can operate in 35 kiloherc, yes.
That frenquency of Tesla coil, I don't know, but I gues, that betwen 500-2000 kiloherc. HV not pulsating, HV have standar sine wave. So is two sine waves. One let say 35 kiloherc, other, let, say, 1500 kiloherc. So I not imagniate how here can be synchronisation and how it can made any influence. See my video, were I showing in last video osciliogram with green sine wave? I here put oscilioscope on resoanant capasitor, who in akula schematic is green. And how you see I get same osciliograme like in ruslan video. Only my kacher frenquency seems lower and lower of it voltage.
:)
hi MenoFather,
Can you advise us how do you obtain the resonance frequency of kacher and you go by tuning a kacher.
This is wild guess at this moment assume 1500khz kacher freq. 1500/4 =375khz .
Tune Tesla coil to run at lower resonance frequency of 375khz via air duct/circular plate/ball or maybe inserting toroid of suitable size into the center which cover length of tesla coil.This toroid part i done before to achieve around this figure 350khz..<400khz.
But in video take note no core was used or spotted in the center of winding.
-
This guessing game is getting most frustrating. Sure would be nice to make a proper correct diagram, for all to use. Maybe someone can make an English translation to the schematic, once we decide which device to replicate.
I still think that the Akula second device is the best bet, with the highest (proven) output.
I use the UF series diodes for my feed back crt rectifier, and they are working fine, as far as I can tell, without any heating. Their DC output can also be going back to the battery, if needed, not just to the oscillator.
Diodes are cheap. Although using 4 diodes for a full bridge rectifier may work better than just using two, like I'm using.
When connecting the HV pulces to the yoke's secondary output coil, as Akula does in his first device, I can feel the HV going all the way to the Mosfets, as well as back to the battery. This can cause some problems, in due time. If I connect the pulser crt output to the earth ground, it kills the oscillations, but connecting it back to the battery positive rail through a CFL bulb substantially improves it's output. Not all transistor will work well for the HV pulcer, as some overheat, or provide much lower output.
-
Dally write, that he divice work and without diodes aditional, but with aditional diodes it work more stable So standar diodes, I think can rectify prety inought well frenquency up to 40 kiloherc, maybe with small eficienty. And maybe Akula remade little PSU (use faster diodes and less indution chokes).
It can operate in 35 kiloherc, yes.
That frenquency of Tesla coil, I don't know, but I gues, that betwen 500-2000 kiloherc. HV not pulsating, HV have standar sine wave. So is two sine waves. One let say 35 kiloherc, other, let, say, 1500 kiloherc. So I not imagniate how here can be synchronisation and how it can made any influence. See my video, were I showing in last video osciliogram with green sine wave? I here put oscilioscope on resoanant capasitor, who in akula schematic is green. And how you see I get same osciliograme like in ruslan video. Only my kacher frenquency seems lower and lower of it voltage.
:)
I would think the HV Coils would have a higher frequency than 37Khz, more likely in Mhz range, I say this due to coil size and wire used. I have a Tesla coil that is almost 24" tall and 4" across (5:1 ratio) and it likes the high 200khz area, I will need to dig up the records but I did sweep it and checked the inductance with a meter, it was around 52mH if I recall using 28Ga. the smaller ones I wound are around 12mH and thus a higher freq.
I have to get back in the lab, too many summer projects around the house keeps me too busy.
SO my take on this design is the HV section is producing energy in the Mhz area. We need to document this type of info, coil inductance, calculated capacitance, sweep the coils for actual operating resonances.Since this design looks to use a phase shift between the PSU (yoke device) and the triggering of the Tesla coil.
Once we document this kind of stuff we can do replications that can duplicate the design/device and will work like the original.
With the above statement, it made me think that we are Hetro-dyning the 2 signals, thus down converting the energy to a frequency which can be manipulated, i.e. the 37khz or 50hz. you still need the correct diodes to rectify to dc and make use of it there. The signal relationship is still critical though, the frequency relationship meaning the harmonic relationship between the 2 signals being mixed. SO we are back to the issue of not knowing the critical component values.
-
I would think the HV Coils would have a higher frequency than 37Khz, more likely in Mhz range,..
I not say, that HV coil is 37 kiloherc. Here yoke and air coil have maybe 37 kiloherc. HV coil have maybe 1.6 megaherc. Ruslan seems use kacher. Kacher holds automatic resonance, but to better fit in 1/4 resonane, HV coil or kacher secondary coil must not be long. So how we see Akula and Ruslan HV coil is not too long.
-
Can you advise us how do you obtain the resonance frequency of kacher and you go by tuning a kacher.Kacher holds automatic resonance. But maybe little you can change resonance, by moving primary coil up or down or if kacher in horisontal position, then to one side or other and maybe puting primary coil not simetrical to secondary... Bysicly you can not much change frenquency of kacher. To change it frenquency, I advice made many secondary coils with diferen number of turns. Let say, one coil have 200 turns, other 300, thryd 400, forth 500, six 600 and chek with that coil is best effect. But how I write in prievous post coil secondary must not be long. :)
This is wild guess at this moment assume 1500khz kacher freq. 1500/4 =375khz .Let say secondary LC resonance is 1500 kiloherc. Let say 1/4 wavelengh, who speed is light speed resonance is 1200 kiloherc. So then maybe you atach 6 turns coil who is on top other coil of akula 2 divice, then maybe LC resonance gose down to 1/4 wave resonance and be 1200 kiloherc also and then maybe you get best effect. But maybe Kacher resonance must be same like pick up coil or one of it layers resonance. :)
-
... Maybe someone can make an English translation to the schematic...
-
More then a single conductor ground cable. As it enters the connection box it is hot glued to the base and you can see more then one wire.
I don't know why the guys that made the video did not take better close ups of the device. What a waste.
Also, that Tesla Coil (TC) should have shocked that guy being so close. There are two possibilities, if the TC is used to transmit energy to
the other coil, then that guy should have been shocked, otherwise the TC is eye candy and I would also presume the other coil is eye candy as well.
I am also having trouble figuring out the logic of having a battery to start the system, but you then use a start/stop switch. That logic is
counter-logic or a prerequisite if you want to fake your device. Such a switch is used when you actually have live power already waiting on
the other side. To prove this is real, that battery should start the system without a switch, then he should remove the battery and see if it keeps
running, then to shut it off, a simple momentary N/C switch is all that is required to open the line and stop the system. Anything more then that
and you can almost be sure there is live power somewhere waiting to be added to the system once the battery start
illusion is accomplished.
I think the greatest inconsistency of the Akula device is the fact that Akula makes no special discussions on the principle of how and why
he wound his coils as they are. Usually, an inventor will come up with a theoretical concept of coil coupling, then produce the coil system and
test it to see if the results match the concept. I do this every day and am sure many other benchers do it as well. But here, all we see is the
coils and there is never discussion about the base concept of the coiling systems. So what this tells me is either the inventor himself has
no clue about the coupling concept, or, most probably because there is no concept because the coiling system is just eye candy.
The point is, the more complicated your coiling system, the more time would have been required in R&D to arrive at that level of complexity because
each coil addition would then create so many more variables that would have to be tested in order to PERFECT the system to operational levels.
So when I see such TK style coiling systems, I ask myself, where did this guy find all the years required to arrive at this complex system? I would
say one guy alone would require a good 10 years of trial and error. So where are the 10 years? Akula has made more systems with varying coil
systems in one year then anyone could do in a lifetime, all alone, all functional and all chock full of discrepancies.
So for me, I think all this fanfare is confirming more and more that all Akula really is interested in is showing things that will steer the public away
from his first yoke device that we have read is licensed to a commercial concern. I have been in business for many decades and could confirm that
any commercial concern knowing he made some public videos of the yoke device, would not appreciate it at all (deal breaker) and that those public
videos may have pushed the licensee to accept the license but conditional that Akula create some distractions so the public can quickly forget
the yoke device, which for me, had more merit in design then all his other jokeronies.
Anyways, looks like we are back to the bench with our own works as this is the only guarantee we will ever have of open sourcing OU.
wattsup
-
Wattsup:
In the some of the Akula videos, as well as his comments, you will find that he does explain at least partially why he has built his circuits as he has. Although after showing his first video device, he didn't want to tell all there is to know about how it works, just shows it working, and some basic explanations. But, many still don't believe or understand how these things work.
In Akulas videos previous to his first device, he explains his test with the induction circuit system, (heating the wrench), from which some of his later devices were derived from.
He also explains that his smaller yoke did not work, and had to use the bigger yokes.
So, not all Tv yokes work the same.
In the first video device, that device was shown running with NO battery, and NO ground connection. Also, keep in mind that his second device was confirmed by Tiger to be working as shown, no fake input source, from the ground wire, or anywhere else. Tiger is no idiot, and has many years experience in this type of devices. I will trust Wesley's word on Tiger, as he knows him well.
Akula who is only about 30 years old, is either a genius, or has had some very qualified and experienced help. And, so has Tariel, especially with the hefty 100kw device. Which I'm sure he did not build, by himself. So, who are the real inventors, that don't want to be known? And who knows what other devices they may have invented, that we have no clue about. As by now even the Black Governments have machines that can do much more than these table top models can. Even the NASA is a front, for the real secret machines being developed in underground bases, and elsewhere. Even saying that they have not been back to the moon in over 40 years. Possible lies to hide what is really going on behind our backs.
Anyways,
I have been studying the Akula second device, (as much as I can actually see of it), as well as the schematic. I'm still very intrigued by it, as ever. As the winding counts don't match the diagram, as well as some other things. The Main air coil is not wound like we have been thinking, either, like 48 48, 24 24, 12 12, (all using a single wire). etz... assuming that the diagram of it is even correct. We don't know the actual turns on any of the coils, wire gauge, former dimensions. Other than the thick outer induction primary coils, that can easily be seen. Nor any other possibly important secret details inside the two white junction boxes.
No voltage/current test points on the diagram, etz... So, and accurate replication is going to be a struggle, at best.
Hats off to Ruslan... who never had anything to do with Akula, if true.
Wattsup, good to see you here.
NickZ
-
I am still waiting some news from this thread before considered as a dead thread about Roman ( Akula ) visiting Germany and hopefully meet Stefan who will do some tests to his device and show the result to us.
...
-
Hi All,
while waiting to verify the truth of the Akula equipment, people to see news from PureEnergySystems.com> News> June 11, 2014 here:
http://pesn.com/2014/06/11/9602508_Maksims-Antonovs_pirates_Akula-free-energy_video_for_Indiegogo-scam/
-
I am still waiting some news from this thread before considered as a dead thread about Roman ( Akula ) visiting Germany and hopefully meet Stefan who will do some tests to his device and show the result to us.
...
You mean like disconnecting the 'earth cable', showing us the make-up of the cable in camera close-up view and then re-terminating it to that dodgy looking earth rod. ;D
-
Ruslan's device is now obtaining 2.2Kw of output. NO dodgy ground. Sorry...
Hoppy, Your negativity is getting the best of you. A time will come, even for you, to realize that what you are adding to these threads, is BS, just Plain BS with NO proof and no validity. That's what's dodgy.
-
Ruslan's device is now obtaining 2.2Kw of output. NO dodgy ground. Sorry...
Hoppy, Your negativity is getting the best of you. A time will come, even for you, to realize that what you are adding to these threads, is BS, just Plain BS with NO proof and no validity. That's what's dodgy.
I hope so Nick.
-
@wattsup:
A great post. You are beginning to see the light. The _real_ light, I mean, not the light that comes from the fakes.
Why doesn't one of the claimants simply send off the smallest self-running apparatus to Stefan Hartmann so he can test it in his own home, himself? Is the device allergic to being sent through the mail? After all, there are no secrets (are there?), we have the schematics (don't we?), we've seen the YT videos of it working without outside power (haven't we?) and the only reason we haven't been able to duplicate Akula/Ruslan/Wesley's performances is because we are too stupid and don't have the magic ferrites, right?
So be a mensch, Wesley or Akula or Ruslan, and help a brother out: Send a working small Akula device to Stefan and let him test and report.
We all know that this will never happen, though. But why not? If I had a working FE device with ten dollars worth of components and an afternoon's labor invested in it... I'd be more than happy to send it off for independent testing, especially after publishing the schematics and the videos. Why not? What would I have to lose?
-
You mean like disconnecting the 'earth cable', showing us the make-up of the cable in camera close-up view and then re-terminating it to that dodgy looking earth rod. ;D
Three shots, two goals, not bad ;D
as the device will be tested far away from radio transmitters, Faraday cage maybe not necessary .
-
this video disappeared, someone has it?
entitled "Free Energy March 2014 Akula0083 Replication pt1"
https://www.youtube.com/watch?v=oAeuE6Y_jxY
-
this video disappeared, someone has it?
entitled "Free Energy March 2014 Akula0083 Replication pt1"
https://www.youtube.com/watch?v=oAeuE6Y_jxY (https://www.youtube.com/watch?v=oAeuE6Y_jxY)
gone already
-
gone already
Videos disappear.
Engineers checking these youtube videos?
-
Hi All,
while waiting to verify the truth of the Akula equipment, people to see news from PureEnergySystems.com> News> June 11, 2014 here:
http://pesn.com/2014/06/11/9602508_Maksims-Antonovs_pirates_Akula-free-energy_video_for_Indiegogo-scam/
I'm not sure that it's actually illegal to copy and use one fake to perpetuate another, what's illegal is soliciting funds based on a lie.
Like the with QEG, Witts cannot go after James and the FTW teams for stealing his work because he is committing a fraud to
begin with. That would be like one of a team of bank robbers stealing one of the other thieves "cut" of the "take" then the thief
who had his take stolen complaining to the police about it. No honor amongst thieves.
If Akula wants to prove something then he should do that. If not then so be it. Speculation is then a given and rightly so.
..
-
Hello! Torrent, to download files over the fuel-less generator Sergey Alexeew. Click here, to download СКАЧАТЬ/DOWNLOAD: https://yadi.sk/d/JSDrPu5BnNvbM
Author this Generator: my.mail.ru/mail/alexeewsergey/ , plus.google.com/u/0/100666972159221696809/posts
Video: m.my.mail.ru/mail/alexeewsergey/video/_myvideo/11.html
email: alexeewsergey@mail.ru
Forum: http://realstrannik.com/forum/freeenergylt-antanas/708-povtorenie-ustanovki-free-energi-kolobukhova?limitstart=0