Don Smith theory

Void: Yes,> MOhm , Thanks.

   Geo:
   Ok, now I understand why your device is showing such low output from just the induction circuits. You are not tuning it to it's best lumin levels, but are tuning it to the RM mode, instead. Which does not light the bulbs very bright by itself, without the Kacher.

   Last night I did the same thing, and tuned to the RM mode using a single 100w bulb, and was able to totally kill the bulb(s) using the hand movements, as you are showing. But, my output at the bulbs, even with the Kacher on is not high enough to power the feed back circuit. As the PS used used for the feed back loop needs to have a minimum of 85v to run it. And my PS does not get that high a voltage to it, yet, after the bulbs, to kick on the PS properly. As I only have about 60v at the bulbs.

   I notice that you do not readjust the TL494 controller trim pots after adding or removing bulbs. This normally needs to be done with every new bulb added. Otherwise you won't get the best frequency sweet spot, as each bulb added changes the running frequency, and so this new frequency needs to be readjusted with every new bulb.  At least that's what I see on my device.
 
   Also now, if the full 600w load of bulbs is on, the device sometimes won't start up depending on the set frequency, and one of the bulbs needs to be unscrewed to allow the system to start up. Once started the third bulb can be added. Just like Ruslan has also shown on his videos.
 
  Any way, I think that I'm getting closer to the way that this device is supposed to work. But, I wish that some of the other guys like Hoppy, apecore, Jed, etz... were also in the game. I'm glad to see that you Geo are still posting your results. Sometimes I feel like I'm the only one left.  But, I know that's not the case.

   Here's a new video that I just uploaded to youtube:
   https://www.youtube.com/watch?v=AW9RCAsStsE&t=457s


   Please start the video from the beginning, as it starts later on, instead. I don't know why it does that.

   

All Hi can I get you to look at this Kapanadze video on this Kapanadze thread please it might give you some in site, I would suggest you go through it frame by frame because I think if you are observant you will considerably notice details to your advantage, watch the original first then Wesleys vid second not referenced here, that's my advice, any comments please.

https://www.youtube.com/watch?v=ceDEIg9ETbA

Also if any one wants to start a pure Kapanadze thread please do so

many thanks and sorry for the intrusion

Allen

  Hey guys:
  Not much going on here lately.

  I've been trying to clean up my act. I'll resume testing shortly.
  My wife said that I was taking up too much room on the kitchen table. So... I gave it a cleaning and some reorganizing.
  But, the camera on my phone seams to be needing a lens cleaning also, as the images are getting blurry.
  Any ways, just trying to keep the thread up.
                                                                   NickZ
 

what is the frequency relationship between kacher and pushpull ?


Is the frequency of the kacher really important? I have seen different configurations with flybacks and other high voltage transformers but it seems to be more important the synchronization with the push pull.

Hi I wouldn't get too carried away with this design if i were you I don't know of any one who has got it to work I have experimented with the best of them and the only gain i found or got was from the push pull circuit and that was with an earth and it was from FERRO resonance and the grenade coil.

The Tesla coil is a different kettle of fish not one of the circuits work correctly as they are ac driven and kill any radiant gain.
one or two guys on here think other wise but not one of them shows a working device, read Tesla's patent and you7 will find 2 films by Peter Linderman that tell you everything as far as i can see they know.

The answere to your question is they both have to be in resonance the katcher and the grenade but the drive circuits have stuff missing and its drive circuits are BS

Allen