Storing Cookies (See : http://ec.europa.eu/ipg/basics/legal/cookies/index_en.htm ) help us to bring you our services at overunity.com . If you use this website and our services you declare yourself okay with using cookies .More Infos here:
https://overunity.com/5553/privacy-policy/
If you do not agree with storing cookies, please LEAVE this website now. From the 25th of May 2018, every existing user has to accept the GDPR agreement at first login. If a user is unwilling to accept the GDPR, he should email us and request to erase his account. Many thanks for your understanding

User Menu

Custom Search

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY  (Read 11715977 times)

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #17445 on: June 20, 2017, 09:39:13 PM »
Nick,

So your 15V regulator for the MOSFET drivers is defective, that part i understand, so replace it.

The rest of your info is not making much sense to me.

first of all, you mean TC4420 for the drivers, as no UC4420 exists, and then you talk about signals at the drain, no drain signals, gate signals are clean but firing at the same time
duty cycle going to 100% etc.

Concerning the screenshots, they show the drain signals? (thats what they are called),
but CH1 is at 2V @ 10x = 20V/div. meaning a square wave signal of about 60V??
CH2 is at 5V @ 1x = 5V/div. meaning a square wave signal of about 12.5V??

Why is CH1 at AC coupled and CH2 DC coupled?

The sequence of these drain signals look OK to me, the upper drain is active (pulling the voltage to ground) when the lower drain is inactive (voltage high).
Duty cycle looks something like 33% (on the gates). This way your MOSFETs should be OK.
Frequency looks very low still (830Hz)

Itsu

AlienGrey

  • Hero Member
  • *****
  • Posts: 3713
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #17446 on: June 20, 2017, 10:00:24 PM »
  Hoppy:
  I've got two filter caps at both the input as well as at the output of the 15v regulator. They are the ones that are recommended by Ruslan's circuit diagram. The 1000uf and also the smaller 104J capacitors, on each side of the regulator. But, if I disconnect the output side of the regulator, I get 24v on the input of the regulator, but no voltage on the output side of the regulator. So, it's gone bad.

  Funny thing though, last night with only 4.2 volts somehow getting to the UC4420 drivers, possibly somehow through the ground side of the regulator, which was still connect up, I WAS getting a square wave signal at the drains. First time.  But, somehow connecting the drivers inputs up to 12v from a battery, I get no drain signals at the drains.
Plus now, not only are the gate signals clean, but they are back to the gates firing at the same time. And the duty cycle going to 100%. So, get that... for a learning curve to unwind.
Try inverting one of the winding going from + volts to the drain.

TinselKoala

  • Hero Member
  • *****
  • Posts: 13958
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #17447 on: June 20, 2017, 10:22:06 PM »
Nick, it is very difficult to interpret your scope "Drain" signals if the channel V/div, input coupling, and probe switch settings are different between the channels.

Please repeat the "Drain" shot with all scope settings the same for both channels (and check the switch on the probe itself as well.) DC coupled, v/div the same for both channels, probe switches on "10x", probe tips at mosfet Drain pins or mosfet tabs (which are also connected to the Drains), probe ground references at Source, ie common negative rail. (Also be quite sure that the mosfet heatsinks do not short the two mosfet Drains together.)

During some time when both Gate signals are firing simultaneously, can you please check the Voltage on the Pin 13 of the 494? This is the "steering" pin. If it sees "ground" or zero voltage, it tells the chip to fire both outputs simultaneously. For normal Push-Pull or alternate output firing, this Pin 13 must see the Vref voltage which appears on Pin 14 from the chip's internal voltage regulator.

Personally, I think it is time to consider scrapping the circuitboard you are using now, and building another unit from scratch, incorporating what you've learned and making the various connections easier to see, understand and work with. And do get your hands on some 8-pin DIP TC4420 driver chips!

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #17448 on: June 20, 2017, 11:58:21 PM »
Nick,

Please take TK's advice and rebuild your board from scratch. Experience tells me that by now with all the alterations you have made, your board must be very messy and a messy board is a breeding place for connection faults.

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #17449 on: June 21, 2017, 12:52:36 AM »
   Well, sorry guys, but I'm not in position to start from scratch, as all I've been doing is starting from scratch, for the last two months or so. The board is not so bad as to chuck it.
   It's not the board at fault, but the builder of it, instead. I could make the same errors on another board if I don't work out what's wrong, at this point.
   
   Don't worry about not being able to see it all clearly, for now. It's a prototype, and I'll figure it all out in time.
The main problem as always, is getting all the needed parts.

  There's a reason that the scope knobs settings are that way, (in different positions). As one of the TL494 channels has higher amplitude than the other, or at least it did. And yes, TK, one of the scope probes was set on 1X and the other on 10X. I corrected that. I'll place the knobs the same in my next pic. No need to try to figure out that last signal. I think that I got it.
  But, even without the 12v or 15v going to the TC4420 drivers, they will give a signal to the drains. Even on as little input as 1.8v. And now when I give these same TC drivers 12v from a battery it cuts off that 1.8v signal it was getting before to the drains. So, I get nothing at the drains when the drivers get the normal 12 or 15v input. But, I do get drain signals, on just the 1.8v input to the drivers, which they get from somewhere.
Just trying to get a grasp on all this. Makes no sense to me, either. But, there's a reason for everything.
 
 

AlienGrey

  • Hero Member
  • *****
  • Posts: 3713
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #17450 on: June 24, 2017, 01:52:01 PM »
According to the attached schematic, the transistor Q3 will invert the output of the NAND Gates in Integrated Circuit U3.
The polarity of the low duty-cycle pulse appearing on the output of U3 is determined by the switch S2.

Also, because Q5 is a N-Channel MOSFET then a positive voltage on its gate will make it conduct between Source and Drain.
If Q5 remains conducting too long then a destructive current will flow through L5, T1 primary and Q5.

P.S.
The attached schematic is identical to yours (identical circuit) but it is translated to English and has four additions:
1) Description: "Monostable Multivibrator"
2) Description: "DSRD Driver"
3) Description altered to: "DSRD Nano Pulser"
4) Component designations.
Hi guys can we just change the subject a moment and get back on track ????????

Have a look at this diagram of the ORIGINAL!  ok
can i draw your attention to this circuit for a while, in particular, the toroid, notice no details are given on this device no ferrox permeability details or winding details and also note the drive is directly connected to the grenade L1 primary, or the matching of an unknown impedance to a High impedance factor I find it unbelievable no one has picked up on this so far, has anyone got any information as I can find nothing on any of the early pages ?

oops just noticed the nano-drive circuit, notice the extra drive inverter transistor ;) err that's going to cause a problem or two ;) perhaps a PNP would do better there.
AG

AlienGrey

  • Hero Member
  • *****
  • Posts: 3713
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #17451 on: June 24, 2017, 02:47:01 PM »
Hi guys!

Posted photos of "green transformers". This is what I found in my pantry. This is a military standard for special transformers, of which there are a huge number of specifications. Produced on the U-shaped cores and toroids. I disassembled the transformer, such as the Dally.
The core is made of an alloy of "alsifer" (aluminium, silicon, iron) or mu - permalloy to avoid saturation. Cores are designed to operate at low frequencies up to 10 kHz, where the use of ferrites impossible.
Dally just picked suitable transformer for his DC-DC converter.
To make such a transformer  I can recommend the rings
made out of u-permalloy.

Regards
Vasiliy
0 special devices !! a yoke ????? hardly 10kh Nickel Mu metal alloy!
It might look like junk but it most certainly is not!

AlienGrey

  • Hero Member
  • *****
  • Posts: 3713
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #17452 on: June 24, 2017, 09:07:34 PM »

forest

  • Hero Member
  • *****
  • Posts: 4076
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #17453 on: June 24, 2017, 10:20:24 PM »
Can someone translate this ?

https://www.youtube.com/watch?v=oi7qViCGa0Q


Why ? It's nothing important, pure speculation about hidden batteries in kapanadze green box. We all know that it's not possible, because of older video with the same coil

PolaczekCebulaczek

  • Full Member
  • ***
  • Posts: 160
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #17454 on: June 25, 2017, 01:53:08 AM »
this old fart Kapanadze does not hidden any batteries, he found a method of transmitting energy in near field through ground, Wesley had seen it, and many russian FE style devices are using this same method.

AlienGrey

  • Hero Member
  • *****
  • Posts: 3713
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #17455 on: June 26, 2017, 09:01:03 PM »
Thanks for the info it's a pity he can't help but I'm sure the idea worked for Henry Moray and Don Smith and others and then there is Nelson Rocha and his BEMF and his resonant standing wave idea that use to plague the Telephone and Telegraph companies back in yesteryear ;)

Regards AG

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #17456 on: June 30, 2017, 05:52:46 PM »
   Looks like things are pretty slow right now on all the forums and threads.
   Nothing new from Akula or Ruslan, nor anyone else, it would seam.

   I have had another delay, due to one or both of my fets going bad on me, again.
However, my TL494 circuit is now working well, but I still need to order some new fets. Hopefully that will be done soon.
   I also had to replace one of the UC4420 fet drivers, which was working when I made my last video, but had since quit on me, also. That UC4420 driver (tiny one) has now been replaced with a new one of the same type.
 So, I'm just waiting for my new fets.

   Does anyone here have anything new and exciting to show???  Don't be shy... Apecore, Geo, or anyone else working on this type of device.

   
   

TinselKoala

  • Hero Member
  • *****
  • Posts: 13958
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #17457 on: June 30, 2017, 09:06:41 PM »
Well, did you look at my last two videos?  They may have some relevance to what you are trying to do. A single mosfet, driven by a TC4420, which is clocked by antenna feedback so as to stay in resonance, that pulses the 3-turn primary of a small Tesla coil, which then shows an interesting effect using a 120v 4w incandescent bulb....

http://www.youtube.com/watch?v=WV3posVDqJs
http://www.youtube.com/watch?v=S_URR6Bk9cg

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #17458 on: July 01, 2017, 01:58:26 AM »
    TK:
   As your battery is being re-charged to some degree by the HV interaction, it would be interesting to see it the battery's charge will last longer, than if there was no feed back current going back into it. Maybe you can try a higher wattage bulb, next time.
   I also wonder what that signal at the battery terminals looks like on your scope. Of course, there may also be some damage caused to the battery with that type of connection methods, in time. Hard to say...
   That antenna idea may also have something in common with the Vasmus devices.  I can also post a link to it if needed.

   Your videos reminded me of one of my videos: https://www.youtube.com/watch?v=mpS7noQZ7DQ
   I've been trying to get that same effect back again, to light a 100w bulb.
 
    I don't know if you've seen the Stalker video, the one showing the lighting a bulb off of a shovel from the HV

   The Poma (or Roma) device has also been replicated by others, and is still one of the most important and simplest devices shown to date. 
   https://www.youtube.com/channel/UC8fOJbjueHyD8BbUigXubmA

AlienGrey

  • Hero Member
  • *****
  • Posts: 3713
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #17459 on: July 01, 2017, 01:58:58 AM »
Well, did you look at my last two videos?  They may have some relevance to what you are trying to do. A single mosfet, driven by a TC4420, which is clocked by antenna feedback so as to stay in resonance, that pulses the 3-turn primary of a small Tesla coil, which then shows an interesting effect using a 120v 4w incandescent bulb....

http://www.youtube.com/watch?v=WV3posVDqJs
http://www.youtube.com/watch?v=S_URR6Bk9cg
Hi Tinsel yes nice work, have you tried using a moving coil Amp meter ? also are you using a 555 driver to your MOS-FET driver ? Psa over here logging on to overunity is becoming a problem it's difficult to know what's going on and who can still log in. Regards AG