Author Topic: Kapanadze Cousin - DALLY FREE ENERGY (Read 11808327 times)

Hoppy · « **Reply #14565 on:** July 26, 2016, 09:26:39 PM »

Quote from: apecore on July 26, 2016, 09:01:49 PM

Ok Hoppy,

Would you be my counterpart?
And feed me with corrections in my approach?
Because expertise is not on my side.

I am no expert in this field either. You need to understand that at this present point in time, there is no correct or incorrect approach, simply personal understandings and opinions.

NickZ · « **Reply #14566 on:** July 28, 2016, 04:01:22 PM »

I've connected my Kacher circuit to run off of the yoke's secondary coil. Which seems to work quite well.
But, the issue that I'm facing is with the bridge rectifier diodes that feed the Kacher's input from the yoke secondary coil, are getting very hot in no time.
I'm using the IN5408 (3 amp) diodes for the bridge, and I'm only using a 12v, 2.5 amp wall adapter to run BOTH the ZVS induction circuits, as well as the Kacher circuit. Any ideas how to solve this diode heating issue?
I'll try to get some of the MUR 460 diodes for building up a new bridge, and mount them on a heatsink.
But, for now the IN5408 will have to do, at least I can see that they do work, although not for long run times.
Jeg, (I believe) has mentioned that he uses the same diodes, and has no overheating problems.

The reason that I'm only using a wall adapter is because I don't have the 18v zener diodes on the induction circuit at this time, so I can't go above the rated voltage going to the mosfet gates. Therefore I'm just using the 12v adapter for now, until I can obtain and replace the 18v 5 watt zeners.

Geo: Thanks for the Vasmus diagram.
Can you tell me what is a "sumator", and how exactly it's built? Used for the same purpose of the "mediator coil"?
I still have the new mediator coil that I built up, but have not installed it yet. Need to get the new zeners on the ZVS circuit, first.
I did notice (a couple of times), that there was an abrupt up in voltage, when syncing up the Kacher to the induction circuits.
But, my rectifiers diodes will overheat after only a minute of running, so I have to turn off the input, which makes me lose the illusive and hard to obtain sync. I've only seen the "extra" output for a several seconds, and only a couple of times.
But, now, I know that it's there...

AlienGrey · « **Reply #14567 on:** July 28, 2016, 10:38:49 PM »

Nick Z High! Re your Grenade coil is built on a strange Dia 1.25 or 1.5 inch pipe note sure of wire length or turns at this moment but the 'F' will be very high so your feeding the diodes you have with a much higher frequency as well, this would make the diodes vibrate and heat up much quicker than anyone else's, I would think this would cause many other issues as well. Tinsel Koala did show a VFO made with a 74HC4046 phase lock chip I would suggest you build it you could then find out the resonant 'F' of the coils you have made, Just a thought that might help you, PS you would need a frequency counter of some sort though or make one. perhaps.

Good luck AG

AlienGrey · « **Reply #14568 on:** July 28, 2016, 10:46:10 PM »

Quote from: GeoFusion on July 26, 2016, 09:16:57 PM

Hi guyz

This is Vasmus schematic of his device, One of the versions.
Something for the forum and many want to try it well here goes.
but I will say there is one thing missing, and is not connected to sumator.
what is it ?

No idea to be honest but, how do you stop the TX and RX sections from wondering around with that circuit as it has a chopper circuit midsection

PS sumat or other ?

NickZ · « **Reply #14569 on:** July 31, 2016, 04:23:54 PM »

Quote from: AlienGrey on July 28, 2016, 10:38:49 PM

Nick Z High! Re your Grenade coil is built on a strange Dia 1.25 or 1.5 inch pipe note sure of wire length or turns at this moment but the 'F' will be very high so your feeding the diodes you have with a much higher frequency as well, this would make the diodes vibrate and heat up much quicker than anyone else's, I would think this would cause many other issues as well. Tinsel Koala did show a VFO made with a 74HC4046 phase lock chip I would suggest you build it you could then find out the resonant 'F' of the coils you have made, Just a thought that might help you, PS you would need a frequency counter of some sort though or make one. perhaps.

Good luck AG

AG: You mentioned that the former tube that I use is strange? It's the same sink drain tube that Ruslan uses. So, it's not strange at all. It is the recommended one shown by Ruslan.
My grenade windings are also the recommended size. 48,48, 24,24, 12,12. 168 turns total for the output coil, and 18.75 meters long for the inductor coil.
You also mentioned that my frequency may too high, and can be causing heating of the rectifier diodes. It's not, I do have a scope, you know. Remember that I'm only using a 12v, 2.5 amp input for BOTH the induction circuit, and the Kacher circuit.
The IN5408 are 1000v, 3 AMP diodes. Yet in a few minutes running they will melt their solder points.
In any case, I'll get the MUR460 diodes and mount them on a heatsink, and replace the ones that I have on presently.
And we'll see what happens, next. If those diodes will heat up, or not.

apecore · « **Reply #14570 on:** July 31, 2016, 04:43:26 PM »

Quote from: NickZ on July 31, 2016, 04:23:54 PM

AG: You mentioned that the former tube that I use is strange? It's the same sink drain tube that Ruslan uses. So, it's not strange at all. It is the recommended one shown by Ruslan.
My grenade windings are also the recommended size. 48,48, 24,24, 12,12. 168 turns total for the output coil, and 18.75 meters long for the inductor coil.

When your pipe diameter is only 1.5inch your output coil length is only 26 meter...... (using the 2.5mm2 solid wire with isolation)
so i guess no 37.5 meter coil length?

NickZ · « **Reply #14571 on:** July 31, 2016, 08:27:37 PM »

No, it's what I said it is, and not 26 meters long. Nor do I use a 1.5 inch PVC pipe.
Nor do I use solid wire, but the stranded wire, like Ruslan/Akula use.

AlienGrey · « **Reply #14572 on:** July 31, 2016, 11:16:59 PM »

Well! Nick Z thank's fo the update and correction to the information. let's hope you get to the bottom of the problem Geo was saying in one of his videos that his grenade coil was getting quite hot (but that's not the diodes) if your really stuck for some fast diodes I have 4 I recovered from a UPS they are good if your stuck i can post them to you, if you want.

Anyway good luck.

br549 · « **Reply #14573 on:** August 02, 2016, 03:09:18 PM »

Quote from: GeoFusion on July 26, 2016, 09:16:57 PM

Hi guyz

This is Vasmus schematic of his device, One of the versions.
Something for the forum and many want to try it well here goes.
but I will say there is one thing missing, and is not connected to sumator.
what is it ?

Hi Guys: I had a question about one of the components shown in the Vasmus drawing. L3 appears to be a coil, but why is it drawn at an angle? Thanks ahead of time for any feedback.

AlienGrey · « **Reply #14574 on:** August 02, 2016, 06:03:12 PM »

Quote from: br549 on August 02, 2016, 03:09:18 PM

Hi Guys: I had a question about one of the components shown in the Vasmus drawing. L3 appears to be a coil, but why is it drawn at an angle? Thanks ahead of time for any feedback.

this is another schematic version, any use ?

GeoFusion · « **Reply #14575 on:** August 02, 2016, 06:30:44 PM »

Hi guyz

NickZ,
I have posted the diagram, it shows you how it's wound and where it's connected.
It's all ferrite core. Vasmus used some strip like ferrite bundle to use it as
a toroidal transformer. There might be differences sins the ferrites are spaced with material.
But ....in this video you can see some guy using the coil configuration in comparison to a standard transformer.
https://www.youtube.com/watch?v=4-flVbCreIM
Yes, in Vasmus device this works as same as what we are referring to as a Mediator, 1 transformer with 90degrees winding with it
with other separate winding(s) that will supply and convert energy at the same time with Synchronization for the circuits connected.
btw, those diodes that overheat are the part of the ZVS circuit?
Remember you will need a good PWM to continue, it's necessary and will be fun.
Fixed frequencies wont do.

AG,
Which ones are you referring to as TX and RX? please let me know

so we can be on the same page.
For what is missing is the Resonator.
Which is another circuit which is in between Tesla and 90 degrees coil with receiver coil, it will be also
connected separately with amount of turns to the Sumator (mediator)
Tesla and Resonator need to be in Synch. for it the produce.
Yes that Schematic can be used as referrence too.
See pic below.

br549,
He has drawn the coil direction on schematic such in a way for him as reminder that it's the
90 degrees coil laying down in between. ( The Horizontal coil )
See Pic below

To clear up some confusion, Recently I have personally tested 3 variations of grenade coils lengths
and to synchronize each one in test conducted and all worked with different results but got the same Synch. effect working.
Just A different resonant freq is to be found each time with different lenght

.
Just follow the resonance when you reach it. You all determine the lenghts of coils, but be aware it needs to stay
in the range that the circuits could handle.

Cheerz~

apecore · « **Reply #14576 on:** August 02, 2016, 11:59:16 PM »

Quote from: GeoFusion on August 02, 2016, 06:30:44 PM

To clear up some confusion, Recently I have personally tested 3 variations of grenade coils lengths
and to synchronize each one in test conducted and all worked with different results but got the same Synch. effect working.
Just A different resonant freq is to be found each time with different lenght .
Just follow the resonance when you reach it. You all determine the lenghts of coils, but be aware it needs to stay
in the range that the circuits could handle.

Cheerz~

Geo thxs for clearafication about the grenade coil length and the resonance adjustment.
So wathever nickz has on his bench he has to ensure resonance

Resonance of kacher/tesla, grenade output coil and inductor is something to perform generally.
But what is your perception about the winding configuratiin of the grenade coutput coil.....
Length is devided in winding configuration
I m focussed now on the interaction of the inductor on the output coil and therefor the way the pickup effect wil be performed by the grenade coil.
Did you in your 3 different configurations used fixed coil windings or did you adjudt them in order to use the same former diameter?
This variable would effect the field configuration..

Meta · « **Reply #14577 on:** August 03, 2016, 12:00:11 AM »

br549,
The 45 degree angle has significance. It may be the 90 degree coil relative to the other standing coils and I also know that a 90 degree rotation of an electron is considered, in Science, to be the definition of a dimension. However 90 degrees in 3D is 180 degrees in 4D (where the real energy is).
So, when we double 90 to 180, we can also halve 90 and arrive at the same 4D energy at 45 degrees...one half of 90, this time....so 45 degrees might indicate real coil position, in 3D, to access 4D energy.
Remember the 45 degree dual Utron energy cones on Otis Carrs levitating discs and the 45 degree rotor on Babbcocks motor. Both access 4D.
Also if you want to know where the 4D unified gravity energy is, in your schematic, its in the center axis of the tubes, right down the middle....so you either have to run your wires thru the middle of the tubes or you have to make the tubes circular and trap the gravity beam inside the tubes and tap it like that. Its just a matter finding a method of tapping the 4D unified gravity beam and then bringing it back down to use it as E and M. This is also the purpose of the 90 degree crossing wires, between relative tubes.

AlienGrey · « **Reply #14578 on:** August 03, 2016, 12:00:32 AM »

Quote from: GeoFusion on August 02, 2016, 06:30:44 PM

Hi guyz

AG,
Which ones are you referring to as TX and RX? please let me know so we can be on the same page.
For what is missing is the Resonator.
Which is another circuit which is in between Tesla and 90 degrees coil with receiver coil, it will be also
connected separately with amount of turns to the Sumator (mediator)
Tesla and Resonator need to be in Synch. for it the produce.
Yes that Schematic can be used as referrence too.
See pic below.

To clear up some confusion, Recently I have personally tested 3 variations of grenade coils lengths
and to synchronize each one in test conducted and all worked with different results but got the same Synch. effect working.
Just A different resonant freq is to be found each time with different length .
Just follow the resonance when you reach it. You all determine the length of coils, but be aware it needs to stay
in the range that the circuits could handle.

Cheerz~

Geo that's so far the best photo I have seen ! To me, I would say the coil on the left is the TX tesla coil and the one on the right is the RX 1/4 wave receiver, you might well get some power gain out of that coil but it's not enough for us novices to get anywhere with without some help.

Have you got a pointer to the Vasmus forum

?? Please ?

NickZ · « **Reply #14579 on:** August 03, 2016, 01:38:32 AM »

Geo, I've connected the yoke secondary coil output to a full bridge rectifier and capacitor, which then goes to the input of the Kacher circuit. And, I've seen the amplification effect three times now.
As the Kacher is being feed by the yoke's main output coil (28t) coil, that's what heats up the rectifier diodes, as there are plenty of amps running there. The grenade output coil (168t) is isolated from any direct connection to the yoke, and just goes to the bulbs, for now. Later to the PS, and then back to the input. That's the plan...
I'm wondering if I double up on the IN5408 diodes that I use on the rectifier, if that will help with their heating issue, or not? Your thoughts...

I've shown on my videos just how I tune the ZVS induction circuits to each other, and also to the Kacher circuit, using ferrite and magnetite. So, there is some control over the frequency, as the frequency is not fixed, like you think. Same with the Kacher circuit, when using ferrite pieces inside of the former tube. But, the coil windings (turn counts) etz, need to be correct in the first place.
I will obtain a TL494 board when I can, and some mosfet drivers, snubber circuit parts. etz... It just takes me forever, as local parts not available, and internet purchases and shipping are not an option for me at this time. And, I'm still looking for commercial alternatives, as well.

So, tell me if your "effect" has enough amplification gain to allow for self running, or not. Or at least, what's going on with that.

News:

User Menu

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY (Read 11808327 times)

Hoppy

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY

AlienGrey

Re: Kapanadze Cousin - DALLY FREE ENERGY

AlienGrey

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY

apecore

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY

AlienGrey

Re: Kapanadze Cousin - DALLY FREE ENERGY

br549

Re: Kapanadze Cousin - DALLY FREE ENERGY

AlienGrey

Re: Kapanadze Cousin - DALLY FREE ENERGY

GeoFusion

Re: Kapanadze Cousin - DALLY FREE ENERGY

apecore

Re: Kapanadze Cousin - DALLY FREE ENERGY

Meta

Re: Kapanadze Cousin - DALLY FREE ENERGY

AlienGrey

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY