Author Topic: Kapanadze Cousin - DALLY FREE ENERGY (Read 11806032 times)

T-1000 · « **Reply #11415 on:** November 29, 2015, 04:40:33 PM »

Quote from: itsu on November 29, 2015, 02:34:17 PM

Oops, another reason to avoid Kachers in your direct environment i guess:

https://www.youtube.com/watch?v=tmFXsMU_myw

Itsu

If you swap Tesla coil with just very high voltage wire acting as electrical field antenna most likely it will be same results. The potential difference in the electrical field is doing all damage there... Also you can always encase entire setup into grounded Faraday cage box so nothing gets radiated out except scalar component from there.

NickZ · « **Reply #11416 on:** December 04, 2015, 02:13:53 PM »

Itsu: You mentioned:
"You will be surprised what little signal you will see ontop of the inductor/Grenade with a 1Kv nano-pulse, certainly no dump wave (ringing?) signal like my kacher did, see around the 6 min. mark."

Maybe the same reason that I'm not seeing any useful results from my Kacher's limited HV output. I believe that I've gotten the Kacher in sync with the induction circuits. Yet, no cigar.
Maybe the Kacher's output needs to be stronger??? However, Geo, as well as Itsu have obtained long HV streamers, (5.000V?),
yet no one has reporting any increased output at the bulbs.

Let's not let this thread die off like all the other projects. Let's keep at it, guys. As there is no better circuit to be working on.
Come on, Tomtech, DA1, Jeg, Geo, Itsu, Hoppy, etz... let's get with it...

itsu · « **Reply #11417 on:** December 04, 2015, 02:59:07 PM »

Nick,

it could be like T-1000 mentioned before, that the coupling of the inductor to grenade is to tight, and therefor the kacher / nano-pulse signals are not "packing a punch".

So we might need to loosen up that coupling so that the kacher / nano pulses are able to disrupt the signals causing the effect to happen.

I am in the process of transforming my Ruslan setup to be nano-pulse driven so i can throw out the kacher.
But that needs some time as i am doing other projects too.

Below a picture of my unfinished new nanopulser which will be driven from 24V input only.
So i create onboard the needed 130V (and with a switch 260V) DC for the MOSFET drain.
It has an onboard VCO so i can test the pulser before hooking it up to the rest of the Ruslan setup.

The heavy cooling on the MOSFET and flyback diode is to be able to get a high pulse repetition frequency (15KHz, hopefully 26KHz).

I think on using 2 DSRD's in series, for a higher voltage pulse, therefor the switchable 130/260V onboard PS.
(the switch switches the 4 diodes behind the yellow ferrite transformer in either FWBR mode (130V) or in voltage double mode (260V).

Regards Itsu

magpwr · « **Reply #11418 on:** December 04, 2015, 04:35:06 PM »

Quote from: itsu on December 04, 2015, 02:59:07 PM

Nick,

it could be like T-1000 mentioned before, that the coupling of the inductor to grenade is to tight, and therefor the kacher / nano-pulse signals are not "packing a punch".

So we might need to loosen up that coupling so that the kacher / nano pulses are able to disrupt the signals causing the effect to happen.

I am in the process of transforming my Ruslan setup to be nano-pulse driven so i can throw out the kacher.
But that needs some time as i am doing other projects too.

Below a picture of my unfinished new nanopulser which will be driven from 24V input only.
So i create onboard the needed 130V (and with a switch 260V) DC for the MOSFET drain.
It has an onboard VCO so i can test the pulser before hooking it up to the rest of the Ruslan setup.

The heavy cooling on the MOSFET and flyback diode is to be able to get a high pulse repetition frequency (15KHz, hopefully 26KHz).

I think on using 2 DSRD's in series, for a higher voltage pulse, therefor the switchable 130/260V onboard PS.
(the switch switches the 4 diodes behind the yellow ferrite transformer in either FWBR mode (130V) or in voltage double mode (260V).

Regards Itsu

hi itsu,

I have got a nanosecond generator PCB which runs on mere 3.5volts.....12volts to power up a modified XL6009 circuit to give 47volts.

Just ask and i shall provide the circuit,prototype pcb and my screenshot from scope.It can do anything up to 1.8Mhz repetition ixdi614 inverted version.
The nanosecond circuit implemented in pcb is the 74hc132 which was posted recently.This was my simplified 1 i/c version.

My nanosecond generator At 1khz it merely consume around 20mA at 35khz at around 460mA at around 1.1kv pulse width 6.8ns...7.4ns.Using 5x kd226d diode in parallel.

But this circuit if interested RF parts alone would set you back around 80usd total mainly from digikey.

2 experiment this circuit can be implemented dally RG58U coax cable and another a high possibility "resonator which is consist of copper sheet coil" base on vasmus.

The descending ripple amplitude as shown in vasmus scope is similar to my experiment in mutisim.

Itsu just ask and i shall give it to you tomorrow.It's late here.

------------------------------------------------
My worst fear seems to be coming true.It seems nearly all the Europe nation is being dragged into this holy war created by isis.As Asian/third party since am no Muslim these fools are trying to create
WWIII.I do feel sorry for those isis fools since they being professionally brainwashed by someone.

Sometimes i wonder which is worst a hypocrite or a two headed snake.

itsu · « **Reply #11419 on:** December 04, 2015, 04:45:47 PM »

Hi Magpwr,

yes sure i would be interested, looks very promising that low voltage / amperage input but still with a nice 1kV output.

Thanks, regards Itsu

NickZ · « **Reply #11420 on:** December 04, 2015, 04:58:22 PM »

Itsu:
Thanks for the pics, that driver circuit looks really nice. I'll be waiting for your results.

You mentioned: "So we might need to loosen up that coupling so that the kacher / nano pulses are able to disrupt the signals causing the effect to happen."

"Loosen up that coupling"? What do you mean?

There is something that has me perplexed. When I watched Geo's video showing how his hand can totally disrupt the entire output at the bulbs. That effect makes me wonder WHY the induction circuit can be disrupted in that way, enough to put out the bulbs. As my circuit does not kill the induction circuit's output, no matter what I do to the Kacher, or where I place my hand.
Maybe Geo can comment on that.

itsu · « **Reply #11421 on:** December 04, 2015, 05:16:16 PM »

Quote from: NickZ on December 04, 2015, 04:58:22 PM

Itsu:
Thanks for the pics, that driver circuit looks really nice. I'll be waiting for your results.

You mentioned: "So we might need to loosen up that coupling so that the kacher / nano pulses are able to disrupt the signals causing the effect to happen."

"Loosen up that coupling"? What do you mean?

There is something that has me perplexed. When I watched Geo's video showing how his hand can totally disrupt the entire output at the bulbs. That effect makes me wonder WHY the induction circuit can be disrupted in that way, enough to put out the bulbs. As my circuit does not kill the induction circuit's output, no matter what I do to the Kacher, or where I place my hand.
Maybe Geo can comment on that.

Well, like adding something inbetween the inductor and the Grenade, like an air gap (foam) or a sheet of copper (with a slit).

Itsu

Jeg · « **Reply #11422 on:** December 04, 2015, 08:24:44 PM »

Hi guys

Nick, I have also experienced this. There are frequencies that look hell steady when I approach my hand close to the antenna or to the grenade. Now I have tuned to a frequency that is very sensitive to the same conditions. The difference between both cases is that the first case uses frequencies that don't belong to my grenade's natural harmonic set of frequencies. The second does use one of this set, and looks quite sensitive when adding external capacitance through my body.

I am waiting for components to make allega's sync board (blue box). Hope that next week I ll be ready to make some tests.

Good work itsu. Can't wait for a video using your new nanopulser.

NickZ · « **Reply #11423 on:** December 04, 2015, 11:52:13 PM »

Itsu:
Loose coupling? I don't know... Your grenade has been wound to the proper specs. Mine may be a little off, here and there.

A controlable TL 494 and PWM board can help to adjust the frequencies for the best waves lengths between the two induction circuits. But, have I personally have not seen much effect at the bulbs, from the addition of Kacher's impulses. Only just a tad, here and there, at times. I don't know if going any lower than 0.5mhz for the Kacher frequency now will help, or not, as it's running frequency has been everywhere else. But, I'll need to get more mag wire to go any lower in frequency, which can take a while to get a hold of the right gauge. In the meantime I'm doing what I can to obtain the "effect".
As always, any ideas are welcome.

forest · « **Reply #11424 on:** December 05, 2015, 09:10:32 AM »

that was called "disruptive discharge" , right ?

magpwr · « **Reply #11425 on:** December 05, 2015, 04:33:12 PM »

Quote from: itsu on December 04, 2015, 04:45:47 PM

Hi Magpwr,

yes sure i would be interested, looks very promising that low voltage / amperage input but still with a nice 1kV output.

Thanks, regards Itsu

hi itsu,

I have just uploaded a crude hd youtube video to demonstrate the 1.1kv nanosecond generator circuit.

The circuit diagram is provided in there.Do check out the test pen lit in free air with nanosecond generator to prove high voltage pulse exist provided with pulse repetition is more than 14.5khz.

http://youtu.be/dyR4GVM99JI

I think the cost exceed $100usd for this nanosecond circuit.

Key components
5x kd226d
MUR10150E x 4
APT10035LLL around $13 in ebay
4 or 7KV High Q 1.8pf...2pf and 100pf SMD capacitor *******Expensive ~$32usd ea
IXDI614 (mosfet driver)
35volts Tantalum capacitor for Mosfet driver
Ceramic capacitors for mosfet driver

35volts 33uf x 2 tantalum polymer capacitor connected in series .*Expensive
Can be replaced with single 15uf 63volts tantalum capacitor.

XL6009 voltage boost circuit x 2.
One of XL6009 circuit to be modified(ss34 to ss36 and output capacitor change to 50volts version) to produce tune 47.1volts max to reach just below 1000volts ...mosfet limit at drain.

smd air inductors current rating around 2Amop...3Amps.
90nH
68nH
47nH

------------------------
Tips output of mosfet driver is placed close to mosfet gate.

Start with low nanosecond pulse at the driver while maintaining 47volts for source.

The mosfet needs 23.5volts ..... 24volts to be provided to mosfet driver IXDI614 in order to function efficiently.

R1 can be anything from 60 to 100 ohms.It does effect pulse width to certain extend.Thick film resistor for smd or 1watt 100ohms resistor will do as well.
-----------------------------

The prototype pcb board does look little ugly since there are many small changes.

itsu · « **Reply #11426 on:** December 05, 2015, 08:48:58 PM »

Thanks Magpwr,

great job, it might be of use for someone especially when you mention it only needs 50V to run with a high repetition rate.

I will stick to my Dally design (modified by verpies) for now.

Regards Itsu

Ed morbus · « **Reply #11427 on:** December 08, 2015, 10:34:52 PM »

Watch
https://www.youtube.com/watch?v=Grt3Me03xSQ

NickZ · « **Reply #11428 on:** December 12, 2015, 04:43:49 PM »

I've been working at tuning my set up the last few days. My best running frequency for the induction circuits is now at 25Khz, while lighting 3 100w bulbs. This is without the full rectification at the output, yet. Only using two UF series diodes in parallel before the bulbs, for now, until I get my 6 amp diodes to make the full bridge rectifier with. Any other diodes heat up.
When I connect my signal generator to the 0.47uf wima capacitor, the best output at the bulbs is obtained at, also 25Khz. Just like the Mazilli. However, if I further adjust this frequency to produce the highest output by moving the ferrite pieces in the grenade core, (while running the Mazilli). This normal resonant frequency (25Khz) drops to about 20Khz, instead, and the bulbs get brighter, but, the signal goes into what Itsu calls the "chaotic mode". However, this new resonant frequency (20Khz) produces the best output at the bulbs.
I still get NO response from my Kacher/grenade sycronization. This is where I'm stuck at...
As there's something that's just not right about my Kacher's running frequency, not being able to influence the induction circuits to any noticeable extent, while scoping the output, and observing the bulbs lumin levels.

Itsu: How are you making out?

Keeping in touch,
NickZ

itsu · « **Reply #11429 on:** December 12, 2015, 09:01:42 PM »

Nick,

sorry to hear you see no improvements, it is where most of us got stuck.

Quote

Itsu: How are you making out?

I just yesterday finished building my new nano-pulser so i can swap it out for the kacher.

I like the 1.4Kv pulse, but i am not satisfied with the gate and drain signals which look terrible.
I think when i can clean those up then the pulse will be higher and/or with less input.

Below first screenshot shows the present 1.4kV pulse i got with 260V on the drain, and the second screenshot shows the terrible gate / drain signals.

In this second screenshot, yellow is the drain voltage, green the drain current (500ma/div.) and blue the gate signal.
Pulse repetition frequency was set to 10Khz which causes the input to be 24V @ 1.5A.
When increasing this p.r.f. to the max. 23KHz of the onboard VCO, it increases the input current to 3A.
By the way, this 2e screenshot was taken with the drain voltage set to 130V!

Video here: https://www.youtube.com/watch?v=NHTwwP8OXDA&feature=youtu.be

Regards Itsu

News:

User Menu

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY (Read 11806032 times)

T-1000

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY

itsu

Re: Kapanadze Cousin - DALLY FREE ENERGY

magpwr

Re: Kapanadze Cousin - DALLY FREE ENERGY

itsu

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY

itsu

Re: Kapanadze Cousin - DALLY FREE ENERGY

Jeg

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY

forest

Re: Kapanadze Cousin - DALLY FREE ENERGY

magpwr

Re: Kapanadze Cousin - DALLY FREE ENERGY

itsu

Re: Kapanadze Cousin - DALLY FREE ENERGY

Ed morbus

Re: Kapanadze Cousin - DALLY FREE ENERGY

NickZ

Re: Kapanadze Cousin - DALLY FREE ENERGY

itsu

Re: Kapanadze Cousin - DALLY FREE ENERGY