Storing Cookies (See : http://ec.europa.eu/ipg/basics/legal/cookies/index_en.htm ) help us to bring you our services at overunity.com . If you use this website and our services you declare yourself okay with using cookies .More Infos here:
https://overunity.com/5553/privacy-policy/
If you do not agree with storing cookies, please LEAVE this website now. From the 25th of May 2018, every existing user has to accept the GDPR agreement at first login. If a user is unwilling to accept the GDPR, he should email us and request to erase his account. Many thanks for your understanding

User Menu

Custom Search

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY  (Read 11717764 times)

Jeg

  • Hero Member
  • *****
  • Posts: 1532
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11400 on: November 22, 2015, 07:15:42 PM »
Jeg,

well yes, almost, i gate straight to the UCC27511 MOSFET driver before the IRFP260.
I know thats 2 drivers behind each other and it will work also without the UCC27511, but that was kind of hard to setup on short notice.

Itsu

Thanks Itsu, I will need some more details on your transformer but I will ask you again when I
ll be there. :)

Jeg

  • Hero Member
  • *****
  • Posts: 1532
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11401 on: November 24, 2015, 02:44:44 PM »
Itsu. :)

I'd like to ask you the range of the pulse's width. I see at the above screenshot 11 ns. Is that the lower width?

In addition what Scotcy diode do you use at the drain of your mosfets?

And about this blue toroid that you used for the output transformer. Where do you find this? Is it from scrap or it needs to have specific permeability?

Thanks

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11402 on: November 24, 2015, 03:56:48 PM »
Hi jeg,

i was afraid you would come up with those questions  :P

The pulse width of 11ns is given/calculated by the scope, i think the standard is to use the width at ½ amplitude (FWHM; Full width at half maximum,
https://en.wikipedia.org/wiki/Full_width_at_half_maximum), but it could depend on the scope.
Perhaps some experts could drop in here.


The schottky diode i have presently in is a D08G60C (http://www.datasheetlib.com/datasheet/383674/d08g60c_infineon-technologies.html)
But the new nano-pulser i am building will be using a D12G60C which is more easily to cool on a heatsink and available in my partsbox.

The blue toroid was one i had in my scrapbox yes, but i lateron switched to the present toroid which is much smaller 10x6x4 and i ordered it from ebay:
(http://www.ebay.nl/itm/T1004-10x6x4mm-Toroidal-Toroid-Ferrite-Core-Filter-Small-size-FT39-10pcs-/370555342978?hash=item5646d1d082:m:m5ynuAj49NNdp_Ag1R7LJQA not sure these are the same i have!!).

Verpies kept track on the used toroids during the Dally replication by severall members early in this thread, see the below post for the data on them.
Mine has severall toroids mentioned, but the 10x6x4 is the one i still use now:
http://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg343496/#msg343496


There is a wealth of information hidden in this thread, so it pays off to take some time to scan through the first 65 pages or so.

Regards Itsu

Jeg

  • Hero Member
  • *****
  • Posts: 1532
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11403 on: November 24, 2015, 05:28:57 PM »
Hi jeg,

i was afraid you would come up with those questions  :P

The pulse width of 11ns is given/calculated by the scope, i think the standard is to use the width at ½ amplitude (FWHM; Full width at half maximum,
https://en.wikipedia.org/wiki/Full_width_at_half_maximum), but it could depend on the scope.
Perhaps some experts could drop in here.


The schottky diode i have presently in is a D08G60C (http://www.datasheetlib.com/datasheet/383674/d08g60c_infineon-technologies.html)
But the new nano-pulser i am building will be using a D12G60C which is more easily to cool on a heatsink and available in my partsbox.

The blue toroid was one i had in my scrapbox yes, but i lateron switched to the present toroid which is much smaller 10x6x4 and i ordered it from ebay:
(http://www.ebay.nl/itm/T1004-10x6x4mm-Toroidal-Toroid-Ferrite-Core-Filter-Small-size-FT39-10pcs-/370555342978?hash=item5646d1d082:m:m5ynuAj49NNdp_Ag1R7LJQA not sure these are the same i have!!).

Verpies kept track on the used toroids during the Dally replication by severall members early in this thread, see the below post for the data on them.
Mine has severall toroids mentioned, but the 10x6x4 is the one i still use now:
http://overunity.com/12736/kapanadze-cousin-dally-free-energy/msg343496/#msg343496


There is a wealth of information hidden in this thread, so it pays off to take some time to scan through the first 65 pages or so.

Regards Itsu

Thanks a lot Itsu.
Indeed too much info but scattered and difficult to find.

Have you measured the limits of your width control? I want some between 60 and 80ns pulse to give rise at 6MHz where I have a good peak on my grenade and inductor together. I used your way to find my resonant points, and until now is the best way that worked for me. I only changed the ground connection of my fg. So I connect my fg red cable to the katcher's antenna, and black cable to the ground of grenade. So signal passes capacitively to grenade. I measured the response of grenade when grenade is fully connected to the bridge-capacitor-load combo. I placed my probe in parallel with grenade, counting also for the 5pf probe's capacitor in parallel with the bridge capacity. I looked for frequencies that excites both inductor and grenade together. I found one at 2Mhz which gives rise at 6Mhz to both of the coils. But firing it straight with 6Mhz the difference in amplitude is big. 

 


itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11404 on: November 24, 2015, 07:32:58 PM »

Jeg,

i measured the width control (R9 in the ALLEGGA blue box) to be between 80ns and 500ns, but that does not "control" the width of the nano-pulse itself when i hooked up my nano-pulser there.
The original width control (74HCT02) of my nano-pulser has some similar range

This nano-pulse width itself is not controlable, it need a minimum input width (i think around 200ns) to function properly but for the rest it
"adjusts" its width to the presented load (50 Ohm resistor or open/closed 50 Ohm coax cable).


But i am not sure if i can follow you, as 70ns corresponds to 14MHz (http://www.calctool.org/CALC/other/converters/freq), so whats that about a 60-80ns pulse and 6MHz?


Itsu

Jeg

  • Hero Member
  • *****
  • Posts: 1532
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11405 on: November 24, 2015, 08:28:43 PM »
Jeg,

i measured the width control (R9 in the ALLEGGA blue box) to be between 80ns and 500ns, but that does not "control" the width of the nano-pulse itself when i hooked up my nano-pulser there.
The original width control (74HCT02) of my nano-pulser has some similar range

This nano-pulse width itself is not controlable, it need a minimum input width (i think around 200ns) to function properly but for the rest it
"adjusts" its width to the presented load (50 Ohm resistor or open/closed 50 Ohm coax cable).


But i am not sure if i can follow you, as 70ns corresponds to 14MHz (http://www.calctool.org/CALC/other/converters/freq), so whats that about a 60-80ns pulse and 6MHz?


Itsu
Hi Itsu.
A six MHz signal has 166ns period. The half cycle has 83ns. If I have a pulse close to this and even narrower then by hitting my grenade with this, it will give rise to its 6Mhz self frequency. It is the same with what you have already done with your last katcher, but in place of katcher secondary now I have my grenade. I just thought that you could control the output pulse width. It would be a nice future.

Page 759 third image of mine. Look how narrow the pulse has to be (compares to the half cycle below on the same image) so to give rise to the corresponded frequency.

I think anything narrower than 80ns is enough for me. If your scope calculated right pulse's width, then 11ns are good for the job.

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11406 on: November 24, 2015, 09:14:47 PM »

Jeg,

Hmmm,  ok,  so you want the nano-pulse to have the same width as a 6MHz half cycle signal (83ns).
But you won't be able to fire this nano-pulse every 83ns.
Max repetition frequency would be around 30KHz i guess, so a 1/2000th of your 6MHz.

Anyway, the best is to find out yourself by building it.

Itsu

Jeg

  • Hero Member
  • *****
  • Posts: 1532
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11407 on: November 24, 2015, 09:23:05 PM »
Jeg,

Hmmm,  ok,  so you want the nano-pulse to have the same width as a 6MHz half cycle signal (83ns).
But you won't be able to fire this nano-pulse every 83ns.
Max repetition frequency would be around 30KHz i guess, so a 1/2000th of your 6MHz.

Anyway, the best is to find out yourself by building it.

Itsu
Yes that was the initial plan. But with one pulse every 15KHz. Then normal I will see a dump wave the same as your last katcher's waveforms.

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11408 on: November 24, 2015, 09:42:21 PM »
Jeg,

i already did this nano-pulse ontop of the grenade signal experiment about 1 year ago, see this video:  https://www.youtube.com/watch?v=Sb0Z-G6fSiE

You will be surprised what little signal you will see ontop of the inductor/Grenade with a 1Kv nano-pulse, certainly no dump wave (ringing?) signal like my kacher did, see around the 6 min. mark.

Itsu

Jeg

  • Hero Member
  • *****
  • Posts: 1532
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11409 on: November 24, 2015, 10:39:17 PM »
I just saw it. Are you aware that by placing your probe in parallel with inductor you tune it at very high frequencies due to the probe's input capacity? Try in parallel with your probe and inductor a variable capacitor. At 300 something pF, I tuned mine at 6Mhz.

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11410 on: November 25, 2015, 10:44:35 AM »

Jeg,

i don't think a 12.5pF / 1Mohm probe has any influence on a 26KHz resonance signal, well at least it should not.
I will take a look at it, but the coil in that video is an old one and not in use anymore (solid copper wire).

Itsu

Jeg

  • Hero Member
  • *****
  • Posts: 1532
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11411 on: November 25, 2015, 06:20:59 PM »
Itsu.
You are right on the fact that by placing your probe in parallel with your inductor, the 26KHz resonance is not affected. This is because inductor is in series with the line which vibrates at 26KHz. But.

  If you place also a parallel to the inductor capacitor, then an other one tank circuit is being formed. This new tank, oscillates inductor to a second frequency the same time. If your probe's capacity is too small, then you probably tune higher than the frequency that your nanosecond pulser is trying to induce.

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11412 on: November 29, 2015, 02:34:17 PM »


Oops, another reason to avoid Kachers in your direct environment i guess:

https://www.youtube.com/watch?v=tmFXsMU_myw

Itsu

AlienGrey

  • Hero Member
  • *****
  • Posts: 3713
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11413 on: November 29, 2015, 03:27:36 PM »

Oops, another reason to avoid Kachers in your direct environment i guess:

https://www.youtube.com/watch?v=tmFXsMU_myw

Itsu

That's why ot's important to select a a good frequency, Eric Dollard  and Tom Brown did some interesting tests on this phenomina and you need to be careful what you are dialing up in frequency.

starcruiser

  • Hero Member
  • *****
  • Posts: 693
    • Starcruiser's Place
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #11414 on: November 29, 2015, 04:31:09 PM »

Oops, another reason to avoid Kachers in your direct environment i guess:

https://www.youtube.com/watch?v=tmFXsMU_myw

Itsu

That looks more like the water in the plant is attracted to the coil