Storing Cookies (See : http://ec.europa.eu/ipg/basics/legal/cookies/index_en.htm ) help us to bring you our services at overunity.com . If you use this website and our services you declare yourself okay with using cookies .More Infos here:
https://overunity.com/5553/privacy-policy/
If you do not agree with storing cookies, please LEAVE this website now. From the 25th of May 2018, every existing user has to accept the GDPR agreement at first login. If a user is unwilling to accept the GDPR, he should email us and request to erase his account. Many thanks for your understanding

User Menu

Custom Search

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY  (Read 11719675 times)

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #9720 on: July 30, 2015, 05:40:13 PM »
   Although this is an older Akula video(below), the wrench heating one, the connections of the yoke primary coil fets, can be seen, along with the center tap of the yoke going to the output side of the driver controller board.  Although this video is not of a self runner, one can see the direction that he took at that point.
   That smaller yoke did not work well, and was replaced with the bigger yoke he uses now. There was only one secondary (3 turns coil), but using no secondary 28 turns yoke coil on this video. The 28 turns secondary coil was added later, and connected to the rectified voltage coming out of the inverter/full bridge recifier, at least on one side that can be clearly seen.
   I believe that the 12v input to the driver board comes through the two wires on the left (yellow and black) from the PS.
   Main point is that, the center tap of the yoke does not get the direct input from the 311v bridge rectifier, as some diagrams show.
 So, at least some of the diagrams may be wrong.
https://www.youtube.com/watch?v=NbJXg0nDRdw

  John.K:
  quote: "Actually he was saying something about possibility to use transformer in connection to have device working at 50-60Hz. Nothing else in details.
                                end quote.

   Can you explain a little more what you mean by that? Please.
 

Dog-One

  • Hero Member
  • *****
  • Posts: 1019
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #9721 on: July 30, 2015, 06:15:07 PM »
I give here another example: see drawing

I wonder myself on PLL-based system and what gives us the phase shift?

The schema using an IR2184...

If you look closely at the chip specifications, it becomes apparent this is a 50% duty cycle device with no possibility of phase shifting.  The 8-pin version has a fixed dead-time.

This is clearly just a standard push-pull driver, with no PWM control.  The clock signal into this device does have PLL lock to adapt to the changing load, but as far as it shifting phases between the two 12 turn windings, no magic there.

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #9722 on: July 30, 2015, 06:17:44 PM »
Hi Hoppy.

Actually he was saying something about possibility to use transformer in connection to have device working at 50-60Hz. Nothing else in details.

His hand sketch shows on the left push-pull. On the right side I think it is pick up coil.  Both synchronised and both grounded as he shows. On the output he draw some filter to not mess up LC tank circuit and the diode bridge.  He says do not ask for schematic. It is very easy to make it if you understand the process.

He step down from granade type because the stability and performance of the device was low.  For Tesla he use the oscillator (not kacher - but can be used if you wish)

That's all in brief.

Thanks John for your reply.

As I commented in an earlier post, I suspect that he is lighting the lamp load to max brightness under a fairly simple resonant circuit. He has very likely not yet achieved a true self-running feedback condition. The grenade coil is both cumbersome and inneficient, thus he has moved to a ferrite toroid based transformer. This all makes sense if he is talking about an induction based modus-operandi. Frequency and pulse width are key to efficiency here to avoid saturating the transformer core, unless he is looking for parametric oscillation condition. I suspect that push-pull should be replaced by a single switched output. My original replication worked more effectively with one of the push-pull mosfets disconnected.

Nick,

A 50Hz frequency of operation would only make sense to me if it was pulses at 50Hz generated with fast edges (non-sinusoidal) to maximise voltage amplification.

Dog-One

  • Hero Member
  • *****
  • Posts: 1019
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #9723 on: July 30, 2015, 11:20:15 PM »
Think I may have stumbled onto something...

Akula's latest video:
https://www.youtube.com/watch?v=E0qVW3zNPkQ

It may be all thermal.  In the case of the Ruslan device, instead of the thermal-magnetic properties of a ferrite pot core, might the same thing happen with copper windings.

I think so.  I think we are tuning against an incorrect operating principal.

Paul Babcock gave us a hint.
« Last Edit: July 31, 2015, 03:36:09 AM by Dog-One »

magpwr

  • Hero Member
  • *****
  • Posts: 1168
    • Youtube Channel
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #9724 on: July 31, 2015, 06:29:22 AM »
hi Tinselkoala or anyone whom got a tesla coil running on mains voltage to reply.

Base on the old video of Akula.I am curious to know roughly how high in kv is needed before we can see sparks at the ferrite rod by touching end of ferrite rod with a metallic object.
I was unable to see spark even at 4.4KV nanosecond pulsing with interrupter.

You seems like a right member to ask since you got a Tesla coil before which is around 1/2 Million volts or more.

https://www.youtube.com/watch?v=CdmKjRQzcWk

My unconfirmed guess is around 30..32kv
-----------------------------

Time to add interrupter on top of my PWM generator PCB. :)

AlienGrey

  • Hero Member
  • *****
  • Posts: 3713
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #9725 on: July 31, 2015, 10:40:09 AM »
In the Akula video he is talking about Neodymion magnets, half way through the video he shows you two types of magnets one is Neodymion but the first one is not, when the Neo magnet gets hot it dies but the first device does not, also did you notice the wire he had round the ferrite, what do you think that might have been ?  ever come across memory wire ? i'm not saying it was but ;)

T-1000

  • Hero Member
  • *****
  • Posts: 1738
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #9726 on: July 31, 2015, 10:57:01 AM »
In the Akula video he is talking about Neodymion magnets, half way through the video he shows you two types of magnets one is Neodymion but the first one is not, when the Neo magnet gets hot it dies but the first device does not, also did you notice the wire he had round the ferrite, what do you think that might have been ?  ever come across memory wire ? i'm not saying it was but ;)
In first part it is iron wire being attracted to stationary neodymium magnet. In the second part there is small neodymium magnet attached to the end of wire. In both cases the heating causes material to change magnetic properties so it gets to non-magnetic state. Doing that rapidly will make induction on the output and the power spent on changing magnetic properties of material is less than power output from induction. This is the point what Roman wanted to show as his LED device is working on same fundamental principle just with non-disclosed method used for changing magnetic properties of material.

P.S> As my personal opinion this smells close to Floyd Sweet VTA http://www.cheniere.org/correspondence/121003.htm where Barium magnetic properties was manipulated...

John.K1

  • Hero Member
  • *****
  • Posts: 679
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #9727 on: July 31, 2015, 11:49:51 AM »
Common guys, you can't change temperature as fast to get any effect from it. That device looks to me bit a joke. Yes I am able to consider to use the temperature  to accelerate electrons, but to heat  wires or magnets in reasonable speed.....?  I think Roman just testing us ;) Better to continue with what Ruslan sais- to play with LC tank cuircuits and HV pulses.   BTW ,if talking about some exotic devices, can somebody tell me this: imagine long square magnet. Now you slice it by 45 degrees. What will be the vector of force for each slice? Will be 45 deg to the surface of each slice or will get back to normal direction ?

Tomtech29

  • Sr. Member
  • ****
  • Posts: 447
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #9728 on: July 31, 2015, 11:57:05 AM »
 :)
good for you at the end of the film can be seen as a screwdriver pad touches the metal cylinder and it is not a magnet, and then says that it is not ferrite why it touches not only the magnet of the same metal!
There is only one permanent magnet! (for what kind of another magnet will not stick to the screwdriver)?
- I've seen it already what was shown in the coil Kapanadze green box

T-1000

  • Hero Member
  • *****
  • Posts: 1738
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #9729 on: July 31, 2015, 12:20:54 PM »
Common guys, you can't change temperature as fast to get any effect from it. That device looks to me bit a joke.
You can change magnetic properties in few ways:
1) With the Curie temperature - https://en.wikipedia.org/wiki/Curie_temperature
2) By making chaos in crystalline structure with the help of magnetostriction - http://journals.aps.org/pr/abstract/10.1103/PhysRev.99.1788
3) By causing NMR in material

So no jokes there... :) And for Roman's case I suspect option 2 due broken ferrite core after prolonged use.

P.S> This make lots of food for thought on Ruslan's device grenade coil operation and what is happening to copper wire as it have 2 signal sources applied where one signal makes it magnet and another makes disruption.

John.K1

  • Hero Member
  • *****
  • Posts: 679
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #9730 on: July 31, 2015, 01:26:07 PM »
T100 - I do not say you can't change magnetic properties. What I say is I think you can't change them quick enough. Not sure what this has to do with ruslan. More closer to his device is the principle of kirschov (or something like that) law, on which base two oposite curents create the kick at their meeting points. Just do what ruslan said and stop comming with such radecilous theory :)

John.K1

  • Hero Member
  • *****
  • Posts: 679
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #9731 on: July 31, 2015, 01:48:12 PM »
Who is native russian speaking here ? I need to know what ruslan said about the direction of the pick up coil and current coil in his last movie I posted here earlier. I had problem to understand if he said they both are wound in the same or opposite direction. I have such feeling he said they are opposite ?

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #9732 on: July 31, 2015, 02:01:56 PM »
Common guys, you can't change temperature as fast to get any effect from it. That device looks to me bit a joke. Yes I am able to consider to use the temperature  to accelerate electrons, but to heat  wires or magnets in reasonable speed.....?  I think Roman just testing us ;)

Agreed!  However, high voltage, short nanosecond pulses can shatter ferrite but its doubtful whether this caused the damage to the ferrite core shown in the video. More like he used an already damaged and repaired pot-core for this device. The use of copper tape is interesting in that this is what some think may have been used by Kapanadze in his early box devices.

Acca

  • Hero Member
  • *****
  • Posts: 563
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #9733 on: July 31, 2015, 02:33:54 PM »
 It’s the Akula secret in the last video…
 
https://www.youtube.com/watch?v=TLhtXQ7Wizo
 
 
https://www.youtube.com/watch?v=Noftcq8g7p8
 
https://www.youtube.com/watch?v=DeLvmi7v7T0
 
https://www.youtube.com/watch?v=l0sGJCabMTY
 
https://www.youtube.com/watch?v=V5iz4aZeQyc
 
https://www.youtube.com/watch?v=cG4fGxVlV7g
 
https://www.youtube.com/watch?v=FXDEAO9SfoE
 
Magnetostriction Magnetostriction is a phenomenon consisting in the fact that when magnetization of a body changes, its volume and linear dimensions change as well. Changing of the body shape can appear, for example, as tension, compression, volume change, which depends both on the acting magnetic field and the crystal structure of the body. The greatest changes in size tend to occur in strongly magnetic materials. During operation many electrical appliances produce noise. Noise of devices powered from household electrical outlet may be similar to buzzing or humming. It is caused by magnetostriction of cores in inductive structures, such as transformers or inductors. When alternating current flows through their coils an alternating magnetic field of the same frequency is created. It causes the ferromagnetic cores to shrink and stretch, which in turn transmit these vibrations to the air and other elements of the design. The magnetostriction phenomenon provides the effect of magnetostrictive transducers and relays, transmitters and receivers of ultrasound, filters and stabilizers in radio frequency devices. Magnetostriction is used to generate the ultrasonic and hypersonic sound. This phenomenon is virtually the only realistic method to generate hypersonic frequency of 1 MHz.
 
Here is the source ….
http://www.etrema.com/
 
 
http://cdn.intechopen.com/pdfs-wm/44683.pdf
 
http://www.alloy-cn.com/sell-terfenol_d_rare_earth_giant_magnetostrictive_alloy-2008474.html
 
http://machinedesign.com/news/designing-galfenol
 
 Acca….[/font]

John.K1

  • Hero Member
  • *****
  • Posts: 679
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #9734 on: July 31, 2015, 02:40:32 PM »
Interesting. Just still donot know how is this applied in Ruslan's device :)