Storing Cookies (See : http://ec.europa.eu/ipg/basics/legal/cookies/index_en.htm ) help us to bring you our services at overunity.com . If you use this website and our services you declare yourself okay with using cookies .More Infos here:
https://overunity.com/5553/privacy-policy/
If you do not agree with storing cookies, please LEAVE this website now. From the 25th of May 2018, every existing user has to accept the GDPR agreement at first login. If a user is unwilling to accept the GDPR, he should email us and request to erase his account. Many thanks for your understanding

User Menu

Custom Search

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY  (Read 11719777 times)

lost_bro

  • Sr. Member
  • ****
  • Posts: 282
    • youtube channel
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7860 on: January 24, 2015, 08:15:33 PM »
hi lost_bro,

I am currently working on PLL in virtual electronics environment. :D

The schematic posted in youtube related to Dave lawton was wrong.Back then i had insufficient experience with PLL.The resistor on pin 11 and pin 12 for 4046 should not be the same.
Resistor value for pin 12 should be higher than pin 11.The original diagram found in internet was worst ,pin 12 on 40426 was left unconnected.This cause the circuit to stop function mid way. :)

This project can be improved further if you can coat the 316L tubes with "Super corona dope"."I can't seems to get this stuff shipped out of USA back then"
I abandon this project due to safety concern due to confined working area."I may resume this project if i have run out of ideas on kapanadze"
My old video revealed what we can achieve using only 1 watt of power <5volts in order to split water.

This was the last video -
1 watt HHO generator ver 2.0 -More bubbles produced with 2 HHO tubes to 1 bifilar coil(Just tap water)
https://www.youtube.com/watch?v=NJw4SSjnejM

HI MagPwr

If I remember correctly Pin#12 is the voltage offset for the Frequency range adjustment and can be left unused.....
His circuit has other limitations/drawbacks that I don't like too much either: ie; Hard switching on the Gating cycle,  the circuit will turn off the MOSFET arbitrarily during ANY part of the Switching waveform.....

Can be corrected by logic gates to time on leading edge and synchronize the switching signal (ZVS), easy mod, use a 4013N or 74HC74D flip-flop > AND gate: Drive signal > CLK & interrupt from GATING > D > AND gate.   Has to wait for cycle to complete before terminating MOSFET drive signal (output of Q only changes on next rising signal edge ).

Funny you should mention Super Corona Dope:  I have a bottle on the shelf from a number of years ago when I played a bit with the DL PLL also.  Never opened it,  one time used standard electrical varnish on the 316L tubes and it adsorbed water and eventually peeled off the tubes.

Sorry for the sidetrack......

Yes, PLL or  a *Phase Lead feedback driver* might be the way to go for small signal/logic control for the Ruslan device.  These are exactly what is used by the DRSSTC builders.  Learned alot myself about signal timing / resonance building SSTCs.  I believe some the same information is applicable in this case also.  Just how to apply it?

take care, peace
lost_bro

EDIT:  forgot to mention the good part of the DL PLL:  I really like the frequency autoscan for resonant freq.    Of course the values Dave used are for just a couple of KHz.....   would need to change some resistor value(s) to get the right frequency for the Ruslan project so the autoscan function and PLL would scan & lock at desired ballpark frequency range. (maybe fix so it will ZVS also)

verpies

  • Hero Member
  • *****
  • Posts: 3473
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7861 on: January 24, 2015, 09:16:33 PM »
This new version is not shown self-running and the lamps are running at very low power in comparison to their ratings.
I am not following this thread much so I don't know what's going on.  I see some scopeshots - that's new!
Could you summarize it for me?  Why has Ruslan switched from a self-powered to externally powered version?
Does he answer questions in Russian?  Is anybody translating his videos to English?

Void

  • Hero Member
  • *****
  • Posts: 2333
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7862 on: January 24, 2015, 09:38:24 PM »
I am not following this thread much so I don't know what's going on.  I see some scopeshots - that's new!
Could you summarize it for me?  Why has Ruslan switched from a self-powered to externally powered version?
Does he answer questions in Russian?  Is anybody translating his videos to English?

Hi Verpies. Ruslan has built several different versions of supposed self running devices, with most of the recent ones
being based somewhat or closely on Akula's second self runner. Ruslan seems to be trying different arrangements to try to
get more output power, and also apparently to try to get a more stable device. Ruslan sometimes posts a video of some testing
he is doing on a new device arrangement before he makes it self running. His latest device is using a lot more
circuitry such as waveform timing sync circuitry, and possibly some circuitry to try to control frequency stability, and
I don't know if he managed to get this latest device self running yet or not.
All the best...

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7863 on: January 24, 2015, 10:50:01 PM »
I am not following this thread much so I don't know what's going on.  I see some scopeshots - that's new!
Could you summarize it for me?  Why has Ruslan switched from a self-powered to externally powered version?
Does he answer questions in Russian?  Is anybody translating his videos to English?

Hi Verpies,

Void has covered the background well. What I find fascinating about Ruslan, is that he is spending a lot of time and effort producing a lot of videos and comes across as a serious experimenter. The waveforms he shows are easily produced from my attempt at replication. However, I have observed nothing that in any way convinces me that his devices actually self-run despite his self-running demos. I feel that he is sincere in believing that Akula has been successful and is trying hard to find the secret by basing his devices on Akula's. I do not think he is holding back anything, rather that he feels the need to fake self-running to seek maximum attention in the hope that others can help him to success by sharing his observations and build details.

John.K1

  • Hero Member
  • *****
  • Posts: 679
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7864 on: January 24, 2015, 11:02:19 PM »
Hoppy, it is exactly how I feel it.  I said it here also before it looks like he is trying to get some infos from Akula ,pretending he knows the technolgy yet. Anyhow, we keep going- the free energy is there somewhere :)

magpwr

  • Hero Member
  • *****
  • Posts: 1168
    • Youtube Channel
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7865 on: January 25, 2015, 02:23:26 AM »
HI MagPwr

If I remember correctly Pin#12 is the voltage offset for the Frequency range adjustment and can be left unused.....
His circuit has other limitations/drawbacks that I don't like too much either: ie; Hard switching on the Gating cycle,  the circuit will turn off the MOSFET arbitrarily during ANY part of the Switching waveform.....

Can be corrected by logic gates to time on leading edge and synchronize the switching signal (ZVS), easy mod, use a 4013N or 74HC74D flip-flop > AND gate: Drive signal > CLK & interrupt from GATING > D > AND gate.   Has to wait for cycle to complete before terminating MOSFET drive signal (output of Q only changes on next rising signal edge ).

Funny you should mention Super Corona Dope:  I have a bottle on the shelf from a number of years ago when I played a bit with the DL PLL also.  Never opened it,  one time used standard electrical varnish on the 316L tubes and it adsorbed water and eventually peeled off the tubes.

Sorry for the sidetrack......

Yes, PLL or  a *Phase Lead feedback driver* might be the way to go for small signal/logic control for the Ruslan device.  These are exactly what is used by the DRSSTC builders.  Learned alot myself about signal timing / resonance building SSTCs.  I believe some the same information is applicable in this case also.  Just how to apply it?

take care, peace
lost_bro

EDIT:  forgot to mention the good part of the DL PLL:  I really like the frequency autoscan for resonant freq.    Of course the values Dave used are for just a couple of KHz.....   would need to change some resistor value(s) to get the right frequency for the Ruslan project so the autoscan function and PLL would scan & lock at desired ballpark frequency range. (maybe fix so it will ZVS also)

hi lost_bro,

You mentoned -Funny you should mention Super Corona Dope:  I have a bottle on the shelf from a number of years ago when I played a bit with the DL PLL also.  Never opened it,  one time used standard electrical varnish on the 316L tubes and it adsorbed water and eventually peeled off the tubes.

Base on old article mention by scientist the Super Corona Dope once applied needs to be cured in a temperature controlled oven or put it out in the mid day Sun for few hours.
This Dope save time on the conditioning the tubes which takes 3 months to get white oxide coating base on their experiment which reduce current between inner/outer tubes and does create larger bubbles.

The white coating is the decompose part of stainless steel 316L.

Lastly please don't forget to sand the tubes "inner tubes outer" and "outer tubes inner side" before applying dope.

That's it.


-
Time to resume experiment with PLL after breakfast. :D

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7866 on: January 25, 2015, 04:22:35 PM »
  Verpies:
   Welcome back!
    I believe that the last Ruslan circuit build is still at the testing stage. And is why he may not have it self running yet. He's trying out different ideas, and driver circuits to see if the Kacher's driver can be replace by taking the input power from the output of the push pull yoke/grenade circuit. Seams to be working so far, but needs to be finished and tuned for higher bulb brightness and best output levels.

  I doubt that all the different circuits that Ruslan has shown are built by him...
He probably has hired someone to professionally make all those different driver circuits, which he then just connects them up to the yoke/grenade coils, to test the results.
Like I wish that I could do...

Ed morbus

  • Full Member
  • ***
  • Posts: 131
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7867 on: January 27, 2015, 10:38:54 PM »

Ed morbus

  • Full Member
  • ***
  • Posts: 131
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7868 on: January 29, 2015, 09:05:10 AM »

Ed morbus

  • Full Member
  • ***
  • Posts: 131
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7869 on: January 29, 2015, 07:09:25 PM »

d3x0r

  • Hero Member
  • *****
  • Posts: 1433
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7870 on: January 29, 2015, 11:40:01 PM »

magpwr

  • Hero Member
  • *****
  • Posts: 1168
    • Youtube Channel
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7871 on: January 30, 2015, 09:18:17 AM »
hi everyone,

There seems to be improvement in PLL circuit diagram released which can be used for Ruslan device.

This morning i just tested out the nanosecond generator in virtual using 74HC132 which is little more simple than my design(less 2 diodes).

The PLL in this circuit is designed to lock onto frequency between 17khz to 42khz.

My experiment revealed the blue toroid is the best one i have in order to generate nice moustache waveform for LM393 or better waveform using TLC272.

-----------------------------------------
The short tesla coil i have previously assembled merely generate around 1.3kv at 30volts using nanosecond pulse at around 27khz  to base of transistor 2SC5200.
I have made a wrong move by removing couple of turns in order to increase frequency to around 1.7Mhz with Antenna.

Using my another tesla coil with few hundred turns(resonance at around 533khz) combine with nanosecond generator did produced "negative ions".

By placing finger near coil i can feel "cool breeze" without getting burned or shocked as long i don't touch wire.
I am very sure by placing small incense candle nearby i can easily make fire to flicker.
The voltage generated from this coil is peaking around 2kv...3kv at 12volts .









Ed morbus

  • Full Member
  • ***
  • Posts: 131
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7872 on: February 02, 2015, 09:09:51 AM »

balphom

  • Newbie
  • *
  • Posts: 17
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7873 on: February 02, 2015, 02:59:13 PM »
Wesley i have learned a lot from the videos you were translating and i have a request that you continue to translate for people like me who don't understand the language of the Russian. Even if  the last video of ruslan. Thanks in advance

Void

  • Hero Member
  • *****
  • Posts: 2333
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #7874 on: February 02, 2015, 06:02:54 PM »
Yes. it would be much appreciated if someone who speaks Russian could maybe provide
at least a brief summary of the important points in Ruslan's latest video, since Ruslan
is going over how he believes all parts of the Akula device work. Maybe there is some new and useful
info in this latest video?
All the best...